|
#2
29th July 2015, 04:33 PM
| |||
| |||
| Re: ONGC Mechanical Question Papers Pdf
ONGC Mechanical Question Papers with answer are as follow: 1 During the execution of a CNC part program block NO20 GO2 X45.0 Y25.0 R5.0 the type of tool motion will be A) circular Interpolation — clockwise B) circular Interpolation — counterclockwise C) linear Interpolation D) rapid feed Answer : (A) 2 A component can be produced by any of the four processes I, II, III and IV. Process I has a fixed cost ofRs. 20 and variable cost of Rs. 3 per piece. Process II has a fixed cost Rs. 50 and variable cost of Re. 1 per piece. Process III has a fixed cost of Rs. 40 and variable cost of Rs. 2 per piece. Process IV has a fixed cost of Rs. 10 and variable cost of Rs. 4 per piece. If the company wishes to produce 100 pieces of the component, from economic point of view it should choose A) Process I B) Process II C) Process III D) Process IV Answer : (B) 3 In an interchangeable assembly, shafts of size 25.000+0.040mm mate with holes of size 25.000+0.020 mm. The maximum possible clearance in the assembly will be A) 10 microns B) 20 microns C) 30 microns D) 60 microns Answer : (D) 4 A company has two factories S1, S2 and two warehouses D1, D2. The supplies from S1 and S2 are 50 and 40 units respectively. Warehouse D1 requires a minimum of 20 units and a maximum of 40 units. Warehouse D2 requires a minimum of 20 units and, over and above, it can take as much as can be supplied. A balanced transportation problem is to be formulated for the above situation. The number of supply points, the number of demand points, and the total supply (or total demand) in the balanced transportation problem respectively are A) 2, 4, 90 B) 2, 4, 110 C) 3, 4, 90 D) 3, 4, 110 Answer : (C) 5 An incompressible fluid (kinematic viscosity, 7.4 x 10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is A) 0.651 x 10-3 B) 0.651 C) 6.51 D) 0.651 x 103 Answer : (B) 6 The tool of an NC machine has to move along a circular arc from (5,5) to (10,10) while performing an operation. The centre of the arc is at (10,5). Which one of the following NC tool path commands performs the above mentioned operation? A) N010 G02 X10 Y10 X5 Y5 R5 B) N010 G03 X10 Y10 X5 Y5 R5 C) N010 G01 X5 Y5 X10 Y10 R5 D) N010 G02 X5 Y5 X10 Y10 R5 Answer : (D) 7 During a Morse test on a 4 cylinder engine, the following measurements of brake power were taken at constant speed. All cylinders firing 3037 kW Number 1 cylinder not firing 2102 kW Number 2 cylinder not firing 2102 kW Number 3 cylinder not firing 2100 kW Number 4 cylinder not firing 2098 kW The mechanical efficiency of the engine is A) 91.53% B) 85.07% C) 81.07% D) 61.22% Answer : (C) 8 In terms of theoretical stress concentration factor (Kt) and fatigue stress concentration factor (Kf ), the notch sensitivity ‘q’ is expressed as A) (Kf -1) (Kt -1) B) (Kf -1) (Kt +1) C) (Kt -1) (Kf -1) D) (Kf +1) (Kt +1) Answer : (A) 9 Starting from x0 = 1, one step of Newton-Raphson method in solving the equation x3 + 3x -7 = 0 gives the next value (x1) as A) x1 = 0.5 B) x1= 1.406 C) x1= 1.5 D) x1 = 2 Answer : (C) 10 The S-N curve for steel becomes asymptotic nearly at A) 103 cycles B) 104 cycles C) 10 6 cycles D) 10 9 cycles Answer : (C) 11. In PERT analysis a critical activity has A) maximum Float B) zero Float C) maximum Cost D) minimum Cost Answer : (B) 12 Environment friendly refrigerant R134a is used inthe new generation domestic refrigerators. Itschemical formula is A) CH C1 F2 B) C2 C13 F3 C) C2 C12 F4 D) C2 H2 F4 Answer : (D) 13 A solid cylinder (surface 2) is located at the centreof a hollow sphere (surface 1). The diameter of the sphere is 1m, while the cylinder has a diameter and length of 0.5 m each. The radiation configuration factor F11 is A) 0.375 B) 0.625 C) 0.75 D) 1 Answer : (C) 14 For a fluid flow through a divergent pipe of length L having inlet and outlet radii of R1 and R2 respectively and a constant flow rate of Q, assuming the velocity to be axial and uniform at any cross-section, the acceleration at the exit is A) 2Q(R1 - R2) p LR23 B) 2Q2 (R1 - R2) p LR23 C) 2Q2 (R1 - R2) p2LR25 D) 2Q2 (R2 - R1) p2LR25 Answer : (C) 15 An incompressible fluid (kinematic viscosity, 7.4 x 10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is A) 0.651 x 10-3 B) 0.651 C) 6.51 D) 0.651 x 103 Answer : (B) ONGC Mechanical Question Paper           |