IES Civil Engineering Exam Question Paper

Will you please provide the Question Paper of IES Civil Engineering Exam ?

[Arun Vats]

Here I am providing the list of few questions of IES Civil Engineering Exam which you are looking for .

1. Consider the following statements Dry rot in timber is due to
1. stacking wood in open areas
2. lack of ventilation
3. decomposition of sap
4. lack of preservatives
Which of the statements given above are
correct ?
a. 1 and 2
b. 1 and 3
c. 2 and 3
d. 3 and 4

2. In static bending test Match List I (Type ofFailure) with List II (Figure) and select thecorrect answer using the codes :
List I
A. Simple tension
B. Gross grain tension
C. Splintering tension
D. Brash tension
List II
1.
2.
3.
4.
A B C D
a. 1 4 3 2
b. 4 1 3 2
c. 4 1 2 3
d. 1 4 2 3

3. Match List I (Pr duct) with List II (Its Use)and select the correct answer using thecodes :
List I
A. Fibre board
B. Heartwood
C. Laminated timber
D. Plywood
List II
1. Panelling
2. Insulation
3. Scantling
4. Arches I trusses
A B C D
a. 3 2 1 4
b. 3 2 4 1
c. 2 3 4 1
d. 2 3 1 4

4. Consider the following characteristics withrespect to brick
1. Minimum compressive strength = 175(Standard units)
2. Minimum absorption is 24 hours, (in %of dry weight) = 12
3. 3. Very little efflorescence
4. Tolerance in dimension = ±8%
As per Indian standards classification, abrick with the characteristics given aboveis termed as
a. H I
b. F Il
c. L II
d. H II








For more questions , here is the attachment

Here I am looking for the last year question paper of IES Civil Engineering Paper II Exam, can you please provide me the same???

[Kiran Chandar]

As you are looking for the last year question paper of IES Civil Engineering Paper II Exam so here I am sharing the same with you

A metallic cube 30 cm side and weighing 450 N is lowered into a tank 'containing a two fluid layer of water and mercury. Top edge of the cube is at water surface. Determine the position of block at waterimercury interface when it has reached equilibrium.

Water is pumped ' from -a well tapping an unconfined aquifer at a rate of 2400. A no-drawdown boundary exists at a distance of 5 km from the well centre. Assuming the well to be fully penetrating, compute the steady state drawdown at the well faces Given Initial saturated thickness = 50m, hydraulic conductivity = 20 mfday, effective well radius =1 m.







Rest of the Questions are attached in below file which is free of cost

Will you please provide the Indian Engineering Service Civil Engineering Exam Question Paper ?

[Arun Vats]

Here is the list of few question of Indian Engineering Service Civil Engineering Exam Question Paper which you are looking for .

1. Match List I (Machinery) with List II
(Purpose) and select the correct answer
using the code given below the Lists :
List I
A. Bulldozer
B. Power shovels
C. Dragline
D. Clamshell
List II
1. Most suited for verticality lifting loose
materials
2. The bucket in this unit digs by pulling
the load towards it
3. To excavate all types of soils and
dump it into trucks
4. For digging the earth at or below the
operating level and loading it to
hauling units
5. Largely employed for excavating and
moving the earth
A B C D
a. 5 3 4 1
b. 1 4 2 5
c. 5 4 2 1
d. l 3 4 5
2. Consider the following statements?
The main reinforcement in the counter fort
in a counter fort retaining wall of R.C.C. is
provided on the
1. inclined face in front of counter fort.
2. bottom face in back counter fort.
3. inclined face n back counterfoil.
4. bottom face in front counterfoil.
Select the correct answer using the code
given below:
a. 1 and 2
b. 2 and 3
c. 3 and 4
d. 2 and 4
3. A doubly reinforced concrete beam has
effective cover d’ to the centre of
compression reinforcement is the depth of
neutral axis, and d is the effective depth to
the centre of tension reinforcement. What
is the maximum strain in concrete at the
level of compression reinforcement?
a. 0.0035 (1–d’/d)
b. 0.0035 (1– d’/xu)
c. 0.002 (1 – d’/xu)
d. 0.002 (1– d’/d)
4. Which one of the following method is
employed to manufacture pre-stressed
concrete sleepers for the railways?
a. Post-tensioning
b. Pre-tensioning
c. Pre-tensioning followed by posttensioning
d. Partial pre-stressing
5. Consider the following statements:
In an under-reinforced concrete beam,
1. Actual depth of neutral axis is less than
the critical depth of neutral axis.
2. concrete reaches ultimate stress prior
to steel reaching the ultimate stress.
3. moment of resistance is less than that
of balanced sections.
4. lever arm of resisting couple is less
than that of balanced sections.
Which of the statements given above are
correct?
a. 1 and 2
b. 1 and 3
c. 2, 3 and 4
d. 1 and 4


Indian Engineering Service Civil Engineering Exam Question Paper