#1
16th April 2015, 04:32 PM
| |||
| |||
GTU EG Paper Solution
Will you please tell me from where I can download the EG Paper with their Solution of the Gujarat Technological University? Will you also provide me the syllabus of the EG Paper so that I can study well? also give me the information about this university? Also provide me the contact details of Gujarat Technological University?
|
#2
17th August 2018, 03:01 PM
| |||
| |||
Re: GTU EG Paper Solution
I want the question paper of Engineering Graphics of First Year Engineering of Gujarat Technological University (GTU) so can you provide me?
|
#3
17th August 2018, 03:03 PM
| |||
| |||
Re: GTU EG Paper Solution
I am providing you the question paper of Engineering Graphics of First Year Engineering of Gujarat Technological University (GTU) GTU B.Tech 1 sem Engineering Graphics question paper Subject Code: 2110013 Subject Name: Engineering Graphics Total Marks: 70 1. Question No. 1 is compulsory. Attempt any four out of remaining Six questions. 2. Make suitable assumptions wherever necessary. 3. Figures to the right indicate full marks. Q.1 Objective Question (MCQ) (a) 1. If the object lies in the fourth quadrant, its position with respect to reference plane will be a) In front of V.P. and above H.P. , b) Behind V.P. and below H.P. c) In front of V.P. and below H.P., d) Behind V.P. and above H.P. 2. In the orthographic projections, F.V. is projected on (a) H.P. (b) V.P. (c) XY (d) GL 3. A square plane is inclined to HP & perpendicular to VP its elevation appears as (a) Rhombus (b) Square (c) Straight line (d) Rectangle 4. When the line is parallel to VP and perpendicular to HP, we can get its true length in ___________. a) Top view b) Front view c) Side view d) Front view & Side view 5. A cone base diameter 40 mm and axis 60 mm is cut by a plane parallel to the base then the true shape will be a)Parabola b) Circle c) Isosceles Triangle d) Regular Triangle 6. Representative fraction is ratio of a) Maximum length/Minimum length b) Actual length of object/Length of object in drawing c) Length of object in drawing/Actual length of object d) All of these 7. While drawing the isometric view of the sphere, its diameter is taken as a) Equal to actual diameter b) 11/9 times of the actual diameter c) 21/9 times of the actual diameter d) none of the above Mark 07 (b) 07 1. In first angle projection method The Left hand side view is placed on a) Above elevation b) Right side of elevation c) below elevation d) Left side of elevation 2. The eccentricity of which of the following curve is greater than one? a) Ellipse b) Hyperbola c) Parabola d) None of above 3. A curved traced out by a point which moves uniformly both about the centre and at the same time away or towards the centre is known as a) Involute b) Cycloid c) Archemedian spiral d) None of above 4. When a line is inclined to VP and parallel to HP, the front view will be _______ to xy. a) parallel b) perpendicular c) inclined at angle φ d) non on these 5. A tetrahedron has ____equal rectangular faces. a) 0 b) 2 c) 3 d) 4 6. The angle between isometric axis is a) 30 b) 90 c) 120 d) 180 7. To obtain the true shape of the section of solid, an auxiliary plane is set at a) Parallel to cutting plane b) Perpendicular to cutting plane c ) Parallel to Ground plane d) Perpendicular to XY Plane (screen shot) Contact- Gujarat Technological University Near Visat Three Roads, Visat - Gandhinagar Highway, Chandkheda, Ahmedabad, Gujarat 382424 079 2326 7521 |