2023 2024 Student Forum > Management Forum > Main Forum

 
  #2  
19th September 2014, 08:18 AM
Super Moderator
 
Join Date: Apr 2013
Re: DMRC Junior Engineer Model Paper

You are looking for Delhi Metro Rail Corporation Junior Engineer Model question Paper, i am providing here:

1. Mho relay is usually employed for the protection of
a) Short lines only
b) Medium lines only
c) Long lines only
d) Any line
Ans: Long lines only
2. A modern power semiconductor device IGBT is combines the characteristics of
a) BJT and MOSFET
b) FCT and GTO
c) SCR and MOSFET
d) SCR and BJT
Ans: BJT and MOSFET
3. For a single-phase a.c. to d.c. controlled rectifier to operate in regenerative
mode, which of the following conditions should be satisfied?
a) Half –controlled bridge, α 90°, source of e.m.f. in load
c) Full-controlled bridge, α > 90°, source of e.m.f. in load
d) Full-controlled bridge, α 90°, source of e.m.f. in load
4. Which is the most suitable power device for high frequency ( more 100 kHz)
switching application?
a) Power MOSFET
b) BJT
c) SCR
d) UJT
Ans: Power MOSFET
5. In a thyristor Latching current is ________ than Holding current
a) Equal
b) Less
c) Greater
d) None

Ans: Greater
6. The transfer function of a system is 10/(1+s) when operating as a unity feedback
system, the steady state error to a step input will be
a) 0
b) 1/11
c) 10
d) Infinity
Ans: 1/11
7. Which one of the following statements for a dc machine which is provided with
inter pole winding (IW) as well as compensating winding (CW) is correct
a) Both IW and CW are connected in series with Armature winding
b) Both IW and CW are connected in parallel with Armature winding
c) IW connected in series but CW is connected in parallel with Armature winding
d) CW connected in series but IW is connected in parallel with Armature winding
Ans: Both IW and CW are connected in series with Armature winding
8. A 0-10 mA PMMC ammeter reads 5mA in a circuit; its bottom control spring
snaps out suddenly the meter will now read.
a) 5mA
b) 10mA
c) 2.5mA
d) 0
Ans: 0
9. A dc cumulatively compounded motor delivers rated load torque at rated speed.
If series field is short circuited, then the armature current and speed will
a) Both increases
b) Both decreases
c) Increases and decreases
d) Decreases and increases
Ans: Both increases
10. Moving coil in dynamometer wattmeter connected
a) In series with fixed coil
b) Across supply
c) In series with load
d) Across load

Ans: Across supply
11. In an induction machine, if the air gap increased
a) Speed will be reduced
b) Efficiency will be improved
c) Power factor will be lowered
d) Breakdown torque will be reduced
Ans: Power factor will be lowered
12. A CRO screen has ten divisions on the horizontal scale. If a voltage signal 5 sin
314t+45 deg)is examined with a line base settings of 5 msec/div, the number of
cycles of signal displayed on the screen will be
a) 0.5 cycles
b) 2.5 cycles
c) 5 cycles
d) 10 cycles
Ans: 2.5 cycles
13. A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of
1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load
are
a) 0.02, 600 W
b) 0.04, 580 W
c) 0.04, 1160 W
d) 0.04, 1200 W
Ans: 0.04, 1160 W
14. Thermocouple is used to measure
a) AC
b) DC
c) Both
d) None
Ans: Both
15. The two watt meters measurement the ratio of two meter readings is –(1-
sqrt3) 1+sqrt3) then the power factor is
a) 1
b) 0.866

c) 0.707
d) 0
Ans: 0.707
16. Hays bridge is used to measure___________ and Schering bridge is used to
measure____________
a) Inductance, Inductance
b) Inductance, Capacitance
c) Capacitance, Inductance
d) Resistance, Capacitance
Ans: Inductance, Capacitance
17. When sine wave is given as input to Schmitt trigger then its generates
a) Sine wave
b) Saw tooth wave
c) Triangle wave
d) Square wave
Ans: Square wave
18. In Gauss Seidel method the following factors are influenced for operation
a) Acceleration factor
b) Selection of slack buss
c) Both
d) None
Ans: Selection of slack buss*
19.
i. (X’+Y’) A. Low-pass filter function
ii. (X’Y’) B. Sum
iii. (XY) C. NAND
D. Carry
E.NOR
a) i-C, ii-E, iii-D
b) i-C, ii-E, iii-B
c) i-C, ii-B, iii-D
d) i-C, ii-E, iii-A

Ans: i-C, ii-E, iii-D
20. The phase lead compensation is used to
a) Increase rise time and decrease overshoot
b) Decrease both rise time and overshoot
c) Increase both rise time and overshoot
d) Decrease rise time and increase overshoot
Ans: Decrease rise time and increase overshoot
21. Voltage feed back amplifier is a
a) Shunt-Shunt
b) Shunt-Series
c) Series-Shunt
d) Series- Series
Ans: Shunt-Shunt
22. In microprocessor the next instruction to be executed is stored in
a) Program Counter
b) Stack Pointer
c) Memory Pointer
d) Accumulator
Ans: Program Counter
23. The following element retains it energy after source is disconnected
a) Resister
b) Inductor
c) Capacitor
d) Thermistor
Ans:
24. In series RLC circuit at resonant
a) Voltage is in phase with current
b) Current is maximum
c) Inductive reactance = Capacitive reactance
d) All of the above

Ans: All of the above
25.For RC low pass filter R=100 K ohms, C= 5 micro farads then lower cutt of
frequency is
a) 1 K HZ
b) 0 HZ
c) 381.3 HZ
d) Infinity
Ans:
26. V=100Sin (1000t+46 deg), I=2Sin (1000t+80 deg) what are the elements in the
circuit
a) R=30 ohm, L=30 mH
b) R=30 ohm, C=33.3 micro farads
c) R=40 ohm, L=30 mH
d) R=40 ohm, L=33.3 micro farads
Ans: R=40 ohm, L=33.3 micro farads


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 06:39 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4