2021 2022 Student Forum > Management Forum > Main Forum

 
  #2  
5th November 2014, 12:48 PM
Super Moderator
 
Join Date: Apr 2013
Re: ABB placement Exam for Instrumentation and Control Engg Preparation Tips

As you want I am here telling you the preparation tips for preparing ABB placement Exam for Instrumentation and Control Engg.

Preparation Tips :

Clear your basic concepts of the subjects.
Be aware about the inventions
Solve previous year paper
Focus On Base Subjects
Prepare according to the syllabus of the exam
Do practice

Sample questions :
(1)in a ckt. We r giving voltage of 50 Hz as well as 60. then what will be
the resultant frequency.
(a)less than 50 (b)more than 60(c)in between 50 & 60
(d)none..........according to our conclusion answer will be none because if
we apply two frequency component resultatnt frequency we can not say with
such an ease.U should confirm the answer
2.In a ckt a single resistor is connected across a d.c. source, what will be
the effect on current in first resistor if we connect one more resistance in
parallel with earlier one....
Answer.. no change since it is a parallel combination.
3.why we don,t like flashover in transmission line (t-line)-
(a ) it may create earth fault(b )it reduces the life of insulator.....
Read something about flashover & puncture.
4.total no of strands in a acsr conductor is 81, then what is the no. of
conductor in its outer layer....(a)36 (b)18 (c)24.......Also read some more
on acsr.
5.Two questions based on p.u. calculation like , p.u. calculation is given
with respect to some old base and u have to calculate it with reference to
new base.
(new resistance/old)=(mva new /mva old)*(old voltage/new voltage)2.
Other question is based upon transfer of p.u calculation in transformer i.e.
how base changes when we we move from primary to secondary or like wise.read
some more on p.u calculation.
6.which table is referred for sag calculation-
(a)stringing chart......answer
7.in a R-L ckt a ac voltage is applied , such that instantaneous power is
negative for 2ms, then what will be the power factor.
(a) 9 deg, (b) 18 deg, (c) 36 Deg...........(I don't know the correct ans)
8. In an incandescent lamp
(a) luminous intensity is more than non-luminous intensity
(b) ,, ,, ,, less ,, ,,
,,
Ans: Since efficiency is less than 100%, hence ans is (b), u should confirm
it further.
9. In which motor no-load to full-load diff. is lowest
(a) series motor, (b) shunt motor, (c) Compound motor
Ans: (b)
10. In a 60Hz induction motor full load speed is 850 rpm then what is the
Synchronous speed. (a) 900 rpm, (b) 950 rpm, (c) 1600
rpm....................Ans: (a)
11. A sync. Motor is running at synch. Speed, if al of sudden D.C.
excitation is removed, then
(a) it will rotate at slip speed, (b) it will stop, (c) it will continue to
rotate at sync. Speed
Ans: (a), because actually it will acts as Induction motor.
12. A transmission line is designed for 50Hz, 440KV. If we want to transfer
power at 60Hz, 440 KV, then the power transfer capability will
(a) decrease, (b) Increase, (c)None
Ans: (a) ...as P=( |Vt| |Ef| sin (delta) ) / X, where (delta) is torque
angle.
13. Increased rotor resistance in rotor ckt of induction motor is related
with
(a) high starting torque, (b) more speed variation,.....................Ans:
(a)
14. In the formulae E = 4.44 f N Ô, Ô is
(a) Avg value, (b) Rms value, (c) Maximum value.....................Ans:
(a)...[confirm it]
15. Voltage & current in a ckt is given by V= V1+j V2 and I= I1 +j I2, then
rms power is
.......(refer book by Edministrator on NETWORK ..)
16. Input impedence of MOSFET is
(a) more than BJT........(Ans)
17, 18. Remember truth table of AND, NOR, NAND, OR, EX-OR ETC...
19. Conversion of Binary number into Equivalent decimal No.
20. Megger is used for the measurement of (a) Insulation resistance, (b)
Conductor resistance.............Ans: (a)
21. Form factor for sinusoidal as well as DC
22. Formulae of Regulation (Vs- Vr)* 100/ Vr, then transmission line is
(a) short transmission line, (b) long, (c) medium...................Ans: (a)
23. Improvement in power factor reduces
(a) power consumed by consumer, (b) power generation, (c) both a &
b...........Ans: (c)
[Confirm it]
24. Read about field test of Series Motor...
25. No-load test for Synchronous motor, the graph is drawn
(a) stator open ckt emf Vs field
26. An AC voltage of 50Hz is impressed in a resistive ckt, the oscillating
power has a frequency (a) 50 Hz, (b) 100, (c) no oscillating power is there
in resistive ckt......Ans: (a)
27. Insulation used in transformer ___________leakage flux.
(a) increases, (b) decreases............Ans: (b)
28.After rain what happens to Insulator (a) break-down strength of Insulator
decreases, (b)Arch length reduces, ..........Ans: (b).....[Confirm it]
29.Diversity factor helps to ............(what ?)
[Read diversity factor, load factor, Reserve capacity factor in depth, with
calculation]
30. Why capacitance is shown as a Shunt element in analysis of transmission
line
(a) it is between Conductor & earth, (b) because Admittance is used for
calculation of capacitive reactance........................Ans: (a)
31. B-R-Y sequence is followed in three phase system, if phase voltage in
B-phase is Vm sin 100, then the phase voltage in R-phase would be (a) Vm
sin (-20)......Ansa)
32. In a particular ckt I = Im Sin (wt -270) and V = Vm Sin wt, then type of
ckt is (a) pure resistive ckt....................[Ans]
33. In a L-R ckt energy lost = 2000 W, energy conserved = 500W, then what is
the time constant...........Ans: time constant = L/R = 0.5
34. In electro-dynamometer A'meter & wattmeter the type of scale is
...Ans:Non-uniform
35. For the same current carrying capacity corona loss of ACSR will be
________than copper conductor. (a) more, (b) less, (c) equal...Ansb)
36. A R-C ckt , supplied with DC, a bulb is connected across the Capacitor,
then what happens to the illumination, if we change the capacitance.
Ans: No change at all
37. Read about surge impendence of over-head and under-ground cable, Surge
impedence formula = sqrt(L/C)
*****[N.B] We are not mentioning the options in sequence, and do not think
that ans for the most questions is option (a). Read all options very
carefully as all are very close to each other.
QUANTITATIVE PAPER + PCM paper
45 Questions ---------45 minutes
1. About 10 quanti questions ( based on Mixture, Work etc. of very easy
type)
2. What is GDP ?
3. Vector algebra, codition for Co-planer vector etc.
4. Gravitation, geo-synchronous satellite( it's hight, orbit , radius
etc.), escape velocity, how g (gravitational accln) varies, about
gravitational potential.
5. Basic electricity and Magnetism----Biot-savart law, current carrying
conductor properties.
6. Nuclear physics, Bohr's constant, and Other theories related .
7. Problem based on VIBGYOR , how wave length and frequency is varying.
8. Questions based on Plank's Theory, E =hv
9. V=u + at , V2=u2 + 2as and W = mgh
questions based on above theory
10. Faraday's laws of electrolysis, m = Zit
11. Heat conduction problem.
12. Co lour-coding of resistor (BBROYGBVGW)
13. How velocity of light changes in different medium while frequency remain
unchanged.
14. statistics , calculation of mode, co-efficient regression (3-4
Questions)
15. f(x) = Sin x + Cos x, find the maximum value of the function.......Ans:
sqrt (2)
16. Formulae for parallel plate capacitor and force between plates.


Tags
placement

Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 04:51 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3