Question Paper Mechanical Engineering KPCL

Can you provide me the KPCL Mechanical question paper for Assistant and Junior Engineer as my sister needs it for preparation?

[Kiran Chandar]

The KPCL Mechanical question paper for Assistant and Junior Engineer as your sister needs it for preparation is as follows:

The chronological order of strokes in a four stroke petrol engine is:
1] Suction stroke, working stroke, compression stroke and exhaust stroke.
2] Suction stroke, compression stroke, working stroke and exhaust stroke.
3] Compression stroke, working stroke, suction stroke and exhaust stroke.
4] Compression stroke, suction stroke, working stroke and exhaust stroke.

The enthalpy of steam is defined as:
1] Difference of internal energy and product of pressure and volume.
2] Product of internal energy and pressure.
3] Sum of internal energy and product of pressure and volume.
4] Amount of heat change divided by the absolute temperature.

Which of the following operations can be performed using a drilling machine?
A. Reaming B. Countersinking C. Spot Facing D.
Thread tapping
1] Only A, B and D 2] Only B, C and D 3] Only A, B and C 4] All of
these

Which of the following are the advantages of impulse turbine over reaction turbines?
A. Occupies less space per unit power.
B. Compounding is not necessary for speed reduction as the rotor speeds are usually low.
C. Suitable for high power generation.
1] B and C only 2] A only 3] C only 4] A and C only

Maximum power transfer through line V1= 110 kv, V2= 100kv, X=22 ohm is
a 500 MW
b 500 KW
c 250 MW
d 250 KW
Ans: 500 MW

Q.Which type of power plant requires maximum expenditure
a Hydel power plants
b Nuclear power plants
c Thermal power plants
d Gas based power plants

Q.Base load of a power station stands for
a 2-4 hours/day
b 4-8 hours/day
c 8-12 hours/day
d 12-24hours/day
Ans: 12-24hours/day

Q.A wire is placed on the top of a transmission line to protect from
a surge high voltage
b Direct lightning strocks
c indirect lightnin strocks
d Switching over voltages
Ans: Direct lightning strocks

Q.A wire is placed on the top of a transmission line acts as
a acts as a phase wire
b acts as neutral
c acts as a transmission wire
d acts as ground wire

Which of the following can be magnified by magnetic amplifier
(a) voltage
(b) current
(c) power
(d) none of above

The inductance is not used in lag network because of
(a) big size
b) time delay and hysteresis losses
(c) high reactance
(d) none of these

Saturation in a stable control system can cause
(a) conditional stability
(b) over damping
(c) low level oscillations
(d) high level oscillations

Excessive noise in control systems can cause
a) reduction in bandwidth
(b) reduction in gain
(c) saturation in amplifying stages
(d) oscillations

The type-0 system has
(a) net pole at the origin
(b) no pole at the origin
(c) simple at one origin
(d) two poles at the origin

In control systems, excessive bandwidth should be avoided because
(a) noise is proportional to bandwidth
(b) it leads to low relative stability
(c) it leads to slow speed of response
(d) none of these

In most systems, an increase in gain leads to
(a) larger damping ratio
(b) smaller damping ratio
(c) constant damping ratio
(d) none of these

A step function is applied to the input of a system and output is of the form y = t, the system is
(a) stable
(b) unstable
(c) not necessarily stable
(d) conditionally stable

The function of the safety resistor in ohm meter is to
(a) limit the current in the coil
(b) increase the voltage drop across the coil
(c) increase the current in the coil
(d) protect the battery

Which of the following instruments is free from hysteresis and eddy current losses?
(a) M.l. instrument
(b) electrostatic instrument
(c) electrodynamometer type instrument
(d)all of these

The dielectric loss of a capacitance can be measured by
(a) Wien bridge
(b) Owen bridge
(c) Schering bridge
(d) Maxwell bridge

Reed frequency meter is essentially a
(a) recording system
(b) deflection measuring system
(c) vibration measuring system
(d) oscillatory measuring system

In measurements made using a Q meter, high impedance elements should preferably be connected in
(a) star
(b) delta
(c) series
(d) parallel

A digital voltmeter measures
(a) peak value
(b) peak-to-peak value
(c) rms value
(d) average value

1. Pick out the one which does not belong to majority of items i.e; the odd thing
a. Leaf spring suspension
b. Coil spring suspension
d. Air suspension
Ans : A

2. Which of the following factors is not related to the effect of independent front suspension
a. Reducing the unsprung masses
b. Reducing tyre wear
d. Elimination of gyroscopic couples
Ans : D

3. The main function of the suspension system is best described as
a. Reducing the body movement
b. Reducing the accelerations to which the body is subjected
Ans : A

4. Helper springs are usually used
a. In heavy vehicles in suspension system to obtain a two stage spring rate
b. In vehicles to improve the load capacity of suspension system
d. To stiffen the suspension
Ans : A

5. Parts of the brake system include brake-shoes and
a. Master brake cylinder
b. Engine cylinders
Ans : C

6. In the power steering assembly having four valves, two distribution and two reaction during neutral, or straight- ahead driving, all four valves are
a. Fully closed
b. Partly open
Ans : C

7. As the steering wheel is turned a worm gear on steering shaft causes the end of the ………….. to swing toward one side or the other of the car
a. King pin
b. Steering gear
Ans : C

8. On the coaxial steering gear, the gear housing is lubricated
a. From the hydraulic system
b. From the worm housing
Ans : A

9. Turning the adjustment screw to make the over centre adjustment causes
a. End-wise movement of the ball nut
b. End-wise movement of the Pitman shaft
d. End-wise movement of steering shaft
Ans : A

10. Air resistance to a car at 20 km/hr is R .The air resistance at 40 km/hr would be
a. R
b. 2R
d. R2
Ans : C

11. Which one of the following is not apart of the chassis
a. Wheels
b. Front axle
d. Passenger seats
Ans : D

12. In the linkage type of power steering system, the piston rod is attached at one end to
a. A tie rod
b. A connecting rod
Ans : B

13. In the linkage type of power steering system, the swinging end of the pitman arm actuates
a. A spool valve
b. A tie rod
d. An idler lever
Ans : B

14. In the constant control power steering unit the spool valve is moved by
a. A pivot lever
b. A valve rotor
Ans : B

15. In the coaxial power steering unit, the spool valve
a. Rotates
b. Moves end-wise
Ans : A

16. In the Saginaw rotary valve unit, rotation of the valve spool from the neutral position results in application of hydraulic oil pressure from the oil pump to one or the other and of the
a. Pitman arm
b. Connecting rod
d. Disc clutch
Ans : C

17. In the Saginaw in line unit, end-wise movement of the valve spool is caused by reaction between the
a. Worm and ball nut
b. Piston and valve
Ans : B

18. In the Saginaw in line power steering unit, the valve spool is centered in neutral by
a. Centering springs
b. Oil pressure
d. Torsion bar
Ans : D

19. Three types of oil pumps used in power steering system are vane, roller and
a. Shoe
b. Slipper
Ans : C

20. The two basic types of power steering system are
a. Integral and valve
b. Booster and power
Ans : C

21. In the steering gear of the linkage connecting to the wheel, steering knuckle, a gear sector, stud or toothed roller is meshed with
a. A worm
b. A ball bearing
Ans : A

22. The steering gear is a device for converting the rotary motion of the steering wheel into
a. To and fro movement
b. Up and down movement
Ans : A

23. In the steering gear, a gear sector or toothed roller is meshed with
a. A Worm
b. A ball bearing
d. Steering wheel
Ans : A

24. The only time the steering wheel requires replacement would be
a. Wheel bearing replacement
b. An accident
Ans : B

25. As the steering wheel is turned a worm gear on the steering shaft causes the movement of the
a. King pin
b. Steering gear
Ans : C

Hii Buddy , Here I am Looking for previous year Karnataka Power Corporation Limited AE/JE Mechanical Engineering Exam Question Paper , Will you please Provide me Same for my help ?

[Raman Vij]

Friend On your Demanding Here I am Providing previous year Karnataka Power Corporation Limited AE/JE Mechanical Engineering Exam Question Paper :

1. When maximum power transfer to load is
a) 20 W
b) 50 W
c) 100W
d) 0W
Ans: 0W

2. Find E in the circuit
a) 5 V
b) 10 V
c) 20 V
d) None
Ans: None

3. Vab is reference then angle between Vab and Ib is
a) -15 deg
b) 240 deg
c) 180 deg
d) -45 deg
Ans: -15 deg

4. When maximum power transfer to load is
Click Here to Show Diagram
a) 20 W
b) 50 W
c) 100W
d) 0W
Ans: 0W

5. Find Zbus Parameters
Click Here to Show Diagram
a) Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm
b)
c)
d)
Ans: Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm

6. Find Z11 and Z12
Click Here to Show Diagram
a) Z11=4 ohm, Z12= 2 ohm
b) Z11=4 ohm, Z12= 5 ohm
c) Z11=5 ohm, Z12= 2 ohm
d) Z11=4 ohm, Z12= 3 ohm
Ans:

7. Current in 5 ohm resister is
Click Here to Show Diagram
a) 10 A
b) -10 A
c) 5 A
d) -5 A
Ans: -10 A

8. Find I in the circuit at t=0+
Click Here to Show Diagram
a) 2 A
b) 5 A
c) 7 A
d) 10 A
Ans: 2 A

9. Find voltage across inductor at t=0+
Click Here to Show Diagram
a) 0 V
b) 2.5 V
c) 5 V
d) 10 V
Ans: 5 V

10. This wave is applied to the PMMC meter, meter reads
Click Here to Show Diagram
a) 0 V
b) 3 V
c) 2 V
d) 1 V
Ans: 1 V

11. Find Vab
Click Here to Show Diagram
a) Zero
b) 50 at an angle of 90 deg
c) 50 at an angle of 90 deg
d) None
Ans:

12. Find E in the circuit
Click Here to Show Diagram
a) 5 V
b) 10 V
c) 20 V
d) None
Ans: None

13. Vab is reference then angle between Vab and Ib is
Click Here to Show Diagram
a) -15 deg
b) 240 deg
c) 180 deg
d) -45 deg
Ans: -15 deg

14. Heat convection, radiation, and conduction all are takes place in
a) Ice
b) Boiler
c) Refrigerator
d) Flue gases in pipe
Ans:

15. When moving iron meter is used to measure d.c current what is the disadvantage
a) It calibration in rms value
b)
c)
d)
Ans:

16. Find Vab
a) Zero
b) 50 at an angle of 90 deg
c) 50 at an angle of 90 deg
d) None
Ans:

17. Find Zbus Parameters
a) Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm
b)
c)
d)
Ans: Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm

18. Find Z11 and Z12
a) Z11=4 ohm, Z12= 2 ohm
b) Z11=4 ohm, Z12= 5 ohm
c) Z11=5 ohm, Z12= 2 ohm
d) Z11=4 ohm, Z12= 3 ohm
Ans:

19. Current in 5 ohm resister is
a) 10 A
b) -10 A
c) 5 A
d) -5 A
Ans: -10 A

20. Find I in the circuit at t=0+
a) 2 A
b) 5 A
c) 7 A
d) 10 A
Ans:

21. Find voltage across inductor at t=0+
a) 0 V
b) 2.5 V
c) 5 V
d) 10 V
Ans: 5 V

22. This wave is applied to the PMMC meter, meter reads
a) 0 V
b) 3 V
c) 2 V
d) 1 V
Ans: 1 V

23. For interrupting capacitive currents which Circuit Breaker (CB) is used
a) SF6 CB
b) Oil CB
c) Vacuum CB
d) Air blast CB
Ans: Vacuum CB

24. For V/F control, when frequency is increased in transformer
a) Core loss component current increases, Magnetizing component current decreases
b) Core loss component current increases, Magnetizing component current increases
c) Core loss component current decreases, Magnetizing component current decreases
d) Core loss component current decreases, Magnetizing component current increases
Ans: Core loss component current decreases, Magnetizing component current decreases

25. In ceiling fan the angle between auxiliary winding a main winding is
a) 0 deg
b) 90 deg
c) 180 deg
d) 360 deg
Ans: 90 deg

26. In a shaded pole motor, shaded rings are used to
a) Field flux production
b)
c)
d)
Ans: Field flux production

27. Practical method of improving string efficiency
a) Increasing crass arms length
b) Using different size of insulators
c) Using different insulator materials
d) Using of guard rings
Ans: Increasing crass arms length

28. In which type of fault all 3-phase components are equal
a) L-G
b) L-L
c) L-L-G
d) 3-Phase fault
Ans: 3-Phase fault

29. 11/220 KV 100 MVA transformers, the primary base voltage rating is 10 KV then secondary base KV is
a) 10 KV
b) 220 KV
c) 220/sqrt3
d)
Ans: 220/sqrt3

30. Water hamming effect is occurs in
a) Surge tank
b) Penstock
c) Turbine
d) Reservoir
Ans: Penstock