|
#4
17th May 2015, 12:24 PM
| |||
| |||
| Re: Sail Management Trainee Exam Papers
Here you are looking to download question papers of Sail Management Trainee Exam, so here I am providing following question papers: Sail Management Trainee Exam Electrical Question Paper 1. Mho relay is usually employed for the protection of a) Short lines only b) Medium lines only c) Long lines only d) Any line Ans: Long lines only 2. A modern power semiconductor device IGBT is combines the characteristics of a) BJT and MOSFET b) FCT and GTO c) SCR and MOSFET d) SCR and BJT Ans: BJT and MOSFET 3. For a single-phase a.c. to d.c. controlled rectifier to operate in regenerative mode, which of the following conditions should be satisfied? a) Half –controlled bridge, a < 90°, source of e.m.f. in load b) Half-controlled bridge, a > 90°, source of e.m.f. in load c) Full-controlled bridge, a > 90°, source of e.m.f. in load d) Full-controlled bridge, a < 90°, source of e.m.f. in load Ans: Full-controlled bridge, a > 90°, source of e.m.f. in load 4. Which is the most suitable power device for high frequency ( more 100 kHz) switching application? a) Power MOSFET b) BJT c) SCR d) UJT Ans: Power MOSFET 5. In a thyristor Latching current is ________ than Holding current a) Equal b) Less c) Greater d) None Ans: Greater 6. The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity Ans: 1/11 7. Which one of the following statements for a dc machine which is provided with inter pole winding (IW) as well as compensating winding (CW) is correct a) Both IW and CW are connected in series with Armature winding b) Both IW and CW are connected in parallel with Armature winding c) IW connected in series but CW is connected in parallel with Armature winding d) CW connected in series but IW is connected in parallel with Armature winding Ans: Both IW and CW are connected in series with Armature winding 8. A 0-10 mA PMMC ammeter reads 5mA in a circuit; its bottom control spring snaps out suddenly the meter will now read. a) 5mA b) 10mA c) 2.5mA d) 0 Ans: 0 9. A dc cumulatively compounded motor delivers rated load torque at rated speed. If series field is short circuited, then the armature current and speed will a) Both increases b) Both decreases c) Increases and decreases d) Decreases and increases Ans: Both increases 10. Moving coil in dynamometer wattmeter connected a) In series with fixed coil b) Across supply c) In series with load d) Across load Ans: Across supply 11. In an induction machine, if the air gap increased a) Speed will be reduced b) Efficiency will be improved c) Power factor will be lowered d) Breakdown torque will be reduced Ans: Power factor will be lowered 12. A CRO screen has ten divisions on the horizontal scale. If a voltage signal 5 sin 314t+45 deg)is examined with a line base settings of 5 msec/div, the number of cycles of signal displayed on the screen will be a) 0.5 cycles b) 2.5 cycles c) 5 cycles d) 10 cycles Ans: 2.5 cycles 13. A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W Ans: 0.04, 1160 W 14. Thermocouple is used to measure a) AC b) DC c) Both d) None Ans: Both 15. The two watt meters measurement the ratio of two meter readings is –(1-sqrt3)  1+sqrt3) then thepower factor is a) 1 b) 0.866 c) 0.707 d) 0 Ans: 0.707 16. Hays bridge is used to measure___________ and Schering bridge is used to measure____________ a) Inductance, Inductance b) Inductance, Capacitance c) Capacitance, Inductance d) Resistance, Capacitance Ans: Inductance, Capacitance 17. When sine wave is given as input to Schmitt trigger then its generates a) Sine wave b) Saw tooth wave c) Triangle wave d) Square wave Ans: Square wave 18. In Gauss Seidel method the following factors are influenced for operation a) Acceleration factor b) Selection of slack buss c) Both d) None Ans: Selection of slack buss* 19. i. (X’+Y’) A. Low-pass filter function ii. (X’Y’) B. Sum iii. (XY) C. NAND D. Carry E.NOR a) i-C, ii-E, iii-D b) i-C, ii-E, iii-B c) i-C, ii-B, iii-D d) i-C, ii-E, iii-A Ans: i-C, ii-E, iii-D 20. The phase lead compensation is used to a) Increase rise time and decrease overshoot b) Decrease both rise time and overshoot c) Increase both rise time and overshoot d) Decrease rise time and increase overshoot Ans: Decrease rise time and increase overshoot 21. Voltage feed back amplifier is a a) Shunt-Shunt b) Shunt-Series c) Series-Shunt d) Series- Series Ans: Shunt-Shunt 22. In microprocessor the next instruction to be executed is stored in a) Program Counter b) Stack Pointer c) Memory Pointer d) Accumulator Ans: Program Counter 23. The following element retains it energy after source is disconnected a) Resister b) Inductor c) Capacitor d) Thermistor Ans: 24. In series RLC circuit at resonant a) Voltage is in phase with current b) Current is maximum c) Inductive reactance = Capacitive reactance d) All of the above Ans: All of the above 25.For RC low pass filter R=100 K ohms, C= 5 micro farads then lower cutt of frequency is a) 1 K HZ b) 0 HZ c) 381.3 HZ d) Infinity Ans: 26. V=100Sin (1000t+46 deg), I=2Sin (1000t+80 deg) what are the elements in the circuit a) R=30 ohm, L=30 mH b) R=30 ohm, C=33.3 micro farads c) R=40 ohm, L=30 mH d) R=40 ohm, L=33.3 micro farads Ans: R=40 ohm, L=33.3 micro farads 27. L=10 mH, I=100Sin50t 0 a) b) c) d) Ans: 28. In dielectric measurement, the dielectric loss is proportional to a) F b) V c) I d) Vsqr Ans: Vsqr 29. G(s) = (1-s)/s(s+2) then closed loop transfer function is a) Unstable b) Stable c) Marginally stable d) All Ans: Stable 30. G(s) = (1+0.5s)/(1+s) find which type of net work it is a) Lead net work b) Lag net work c) Lag - Lead net work d) Lead - Lag net work Ans: Lag net work 31. Temperature of electrode in Arc furnace is a) 1000 deg b) 1500 deg c) 1500 deg to 3500 deg d) 4500 deg Ans: 32. In bode plot the point which separates the lower and upper frequencies is called a) Critical point b) Cut-off point c) d) Ans: 33. Nyquest stability is used to determine a) Absolute Stability b) Relative Stability c) Both d) None Ans: Both* 34. When 220V dc shunt alternator generating the voltage at rated value. If direction of rotation is reversed, then alternator will a) Build up its voltage with same polarity b) Build up its voltage with opposite polarity c) No build up of voltage d) None Ans: No build up of voltage 35. Over lap Angle depends on_________ a) Load inductance b) Loa capacitance c) Source inductance d) Source capacitance Ans: Source inductance 36. Area under speed time curve gives a) Time b) Speed c) Distance d) None Ans: Distance 37. The regulation of Short Transmission lines depends up on a) Distance of line b) Frequency c) Power factor d) All Ans: Power factor 38. Which of the following plant is having lowest load factor? a) Diesel Plant b) Pumped storage Plant c) Thermal Plant d) Nuclear Plant Ans: Diesel Plan 39. For SR latch whent the out put is undesirable a) 0, 0 b) 1, 0 c) 0, 1 d) 1, 1 Ans: 1, 1 40. For interrupting capacitive currents which Circuit Breaker (CB) is used a) SF6 CB b) Oil CB c) Vacuum CB d) Air blast CB Ans: Vacuum CB 41. For V/F control, when frequency is increased in transformer a) Core loss component current increases, Magnetizing component current decreases b) Core loss component current increases, Magnetizing component current increases c) Core loss component current decreases, Magnetizing component current decreases d) Core loss component current decreases, Magnetizing component current increases Ans: Core loss component current decreases, Magnetizing component current decreases 42. In ceiling fan the angle between auxiliary winding a main winding is a) 0 deg b) 90 deg c) 180 deg d) 360 deg Ans: 90 deg 43. In a shaded pole motor, shaded rings are used to a) Field flux production b) c) d) Ans: Field flux production 44. Practical method of improving string efficiency a) Increasing crass arms length b) Using different size of insulators c) Using different insulator materials d) Using of guard rings Ans: Increasing crass arms length* 45. In which type of fault all 3-phase components are equal a) L-G b) L-L c) L-L-G d) 3-Phase fault Ans: 3-Phase fault 46. 11/220 KV 100 MVA transformers, the primary base voltage rating is 10 KV then secondary base KV is a) 10 KV b) 220 KV c) 220/sqrt3 d) Ans: 220/sqrt3* 47. Water hamming effect is occurs in a) Surge tank b) Penstock c) Turbine d) Reservoir Ans: Penstock 48. Transient stability can be improved by a) By putting series capacitor b) By using dynamic resister c) Auto re-closers d) All of the above Ans: All of the above 49. If sending end voltage is Vs at no-load in a transmission line then receiving end voltage is if ABCD parameters of line is given a) Vs b) Vs/A c) 0 d) Infinity Ans: Vs/A 50. Harmonics are eliminated by using a) Skewing of rotor b) Distribution winding c) Short pitch winding d) All of the above Ans: All of the above 51. For parallel operation of transformer at no load, then load shared are equal when a) Impedance is proportional with respect to own KVA rating b) c) d) Ans: Impedance is proportional with respect to own KVA rating 52. In Induction motor Slip frequency of rotor current, when rotor speed is Nr. Then rotor producing slip field rotates with respect to stator is a) Slip frequency b) Nr c) Ns d) None Ans: Ns 53. Good regulation means a) Less fluctuations from no-load to full-load b) c) d) Ans: Less fluctuation from no-load to full-load 54. At dead short circuit at terminals of Alternator then the current I is a) ZPF Lag b) ZPF lead c) Unity power factor d) 0.8 Power factor lag Ans: ZPF Lag 55. Full scale Ammeter reading is 10 mA, Voltage across Ammeter is 100 mV. Then for 100 A measurements the power loss in the circuit is a) 1 W b) 10 W c) 100 W d) 1000 W Ans: 10 W* 56. When Alternator excitation increases and machine is operating at lagging power factor then a) I increase b) I decreases c) No effect on current d) None Ans: I increase 57. Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney Ans: Economizer 58. Two alternators rated are 200 KW at 4% regulation, 400 KW 5% regulation operating in parallel at 50HZ , when supply 600 KW the new frequency is a) 50 b) 49 c) 51.3 d) 47.7 Ans: 47.7 59. Va and Vb are negative sequence component voltages the difference angle between Va and Vb with respect to Va is a) 240 b) 120 c) 180 d) 360 Ans: 120 60. 4-Quadrent operation of chopper I is positive but V is may be positive are negative operates in which quadrant a) 1 and 2 b) 2 and 3 c) 1 and 3 d) 1 and 4 Ans: 1 and 4 61. Heat convection, radiation, and conduction all are takes place in a) Ice b) Boiler c) Refrigerator d) Flue gases in pipe Ans: 62. When moving iron meter is used to measure d.c current what is the disadvantage a) It calibration in rms value b) c) d) Ans: 63. When maximum power transfer to load is a) 20 W b) 50 W c) 100W d) 0W Ans: 0W 64. Find Zbus Parameters a) Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm b) c) d) Ans: Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm 65. Find Z11 and Z12 a) Z11=4 ohm, Z12= 2 ohm b) Z11=4 ohm, Z12= 5 ohm c) Z11=5 ohm, Z12= 2 ohm d) Z11=4 ohm, Z12= 3 ohm Ans: 66. Current in 5 ohm resister is a) 10 A b) -10 A c) 5 A d) -5 A Ans: -10 A 67. Find I in the circuit at t=0+ a) 2 A b) 5 A c) 7 A d) 10 A Ans: 8. Find voltage across inductor at t=0+ a) 0 V b) 2.5 V c) 5 V d) 10 V Ans: 5 V 69. This wave is applied to the PMMC meter, meter reads a) 0 V b) 3 V c) 2 V d) 1 V Ans: 1 V 70. Find Vab a) Zero b) 50 at an angle of 90 deg c) 50 at an angle of 90 deg d) None Ans: 71. Find E in the circuit a) 5 V b) 10 V c) 20 V d) None Ans: None 72. Vab is reference then angle between Vab and Ib is a) -15 deg b) 240 deg c) 180 deg d) -45 deg Ans: -15 deg* 63. When maximum power transfer to load is Click Here to Show Diagram a) 20 W b) 50 W c) 100W d) 0W Ans: 0W 64. Find Zbus Parameters Click Here to Show Diagram a) Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm b) c) d) Ans: Z11=Z12=Z21= j0.1 ohm, Z22=j0.3 ohm 65. Find Z11 and Z12 Click Here to Show Diagram a) Z11=4 ohm, Z12= 2 ohm b) Z11=4 ohm, Z12= 5 ohm c) Z11=5 ohm, Z12= 2 ohm d) Z11=4 ohm, Z12= 3 ohm Ans: 66. Current in 5 ohm resister is Click Here to Show Diagram a) 10 A b) -10 A c) 5 A d) -5 A Ans: -10 A 67. Find I in the circuit at t=0+ Click Here to Show Diagram a) 2 A b) 5 A c) 7 A d) 10 A Ans: 2 A 68. Find voltage across inductor at t=0+ Click Here to Show Diagram a) 0 V b) 2.5 V c) 5 V d) 10 V Ans: 5 V 69. This wave is applied to the PMMC meter, meter reads Click Here to Show Diagram a) 0 V b) 3 V c) 2 V d) 1 V Ans: 1 V 70. Find Vab Click Here to Show Diagram a) Zero b) 50 at an angle of 90 deg c) 50 at an angle of 90 deg d) None Ans: 71. Find E in the circuit Click Here to Show Diagram a) 5 V b) 10 V c) 20 V d) None Ans: None 72. Vab is reference then angle between Vab and Ib is Click Here to Show Diagram a) -15 deg b) 240 deg c) 180 deg d) -45 deg Ans: -15 deg* 1. A definite area or space where some thermodynamic process takes place is known as A thermodynamic system B thermodynamic cycle C thermodynamic process D thermodynamic law 2. Which of the following is an intensive property of a thermodynamic system? A volume B Temperature C mass D energy 3. Temperature at which the volume of the gas becomes 0 is called A absolute scale of temperature B absolute 0 temperature C absolute temperature D none of these 4. The unit of energy in SI units is A joule B joule metre C watt D joule/metre 5. 1 joule is equal to A 1 Nm B kNm C 10 Nm/s D 10 kNm/s 6. In an irreversible process there is a A loss of heat B no loss of heat C gain of heat D no gain of heat 7. The following is an SI engine A diesel engine B petrol engine C gas engine D none of the above 8. In a 4 stroke cycle petrol engine during suction stroke A only air is sucked in B only petrol is sucked in C mixture of petrol and air is sucked in D none of the above 9. The thermal efficiency of petrol engine as compared to diesel engine is A lower B higher C same for same power output D same for same speed 10. Compression ratio of diesel engines may have a range A 8 to 10 B 10 to 15 C 16 to 20 D none of the above 11 The thermal efficiency of good I.C engine at the rated load is in the range of A 80 to 90% B 60 to 70% C 30 to 35% D 10 to 20% 12 Carburettor is used for A SI engines B gas engines C CI engines D none of the above 13 In SI engine to develop high voltage for spark plug A battery is installed B distributor is installed C carburetor is installed D ignition coil is installed 14 In a four cylinder petrol engine the standard firing order is A 1-2-3-4 B 1-4-3-2 C 1-3-2-4 D 1-3-4-2 15 The knocking is SI engines increases with A increase in inlet air temperature B increase in compression ratio C increase in cooling water temperature D all of the above 16 Petrol commercially available in India for Indian passenger cars has octane number in the range A 40 to 50 B 60 to 70 C 80 to 85 D 95 to 100 17 The knocking tendency in C.I engines increases with A decrease of compression ratio B increase of compression ratio C increasing the temperature of inlet air D increasing cooling water temperature 18 The air standard otto cycle comprises A two constant pressure processes and two constant volume processes B two constant pressure and two constant entropy processes C two constant volume processes and two constant entropy processes D none of the above 19 The thermal efficiency of theoretical otto cycle A increases with increase in compression ratio B increases with increase in isentropic index gamma C does not depend upon the pressure ratio D follows of the above 20 Thermal efficiency of a gas turbine plant has compared to diesel engine plant is A higher B lower C same D may be higher or lower 21 Mechanical efficiency of a gas turbine as compared to internal combustion Reciprocating engine is A higher B lower C same D unpredictable 22 For a gas turbine the pressure ratio may be in the range A 2 to 3 B 3 to 5 C 16 to 18 D 18 to 22 23 Thermal efficiency of a closed cycle gas turbine plant increases by A reheating B intercooling C regenerator D all of the above 24With the increase in pressure ratio thermal efficiency of a simple gas turbine Plant with fixed turbine inlet temperature A decreases B increases C first increases and then decreases D first decreases and then increases 25In two stage turbine plant, reheating after first stage A increases work ratio B decreases work ratio C does not affect work ratio D none of the above 26For a jet propulsion unit , ideally the compressor work and turbine work are A equal B unequal C not related to each other D unpredictable 27 Various kinematic pairs are given below.choose the lower pair A ball bearings B tooth gears in mesh C camm and follower D crank shaft and bearing 28The relation between the number of pairs forming a kinematic chain and the Number of links is A l=2p-2 B l=2p-3 C l=2P-4 D l=2p-5 29In a reciprocating engine A crankshaft and flywheel form 2 kinematic links B crankshaft and flywheel form 1 kinematics links C crankshaft and flywheel do not form kinematic links D flywheel and crankshaft separately form kinematic links 30A kinematic chain is known as a mechanism when A none of the link is fixed B one of the links is fixed C two of the links are fixed D all of the links are fixed 31 Which of the following is an inversion of single slider crank chain? A beam engine B watt’s indicator mechanism C elliptical trammels D whitworth quick return motion mechanism 32 control volumes refer to A a fixed region in space B a specified mass C an isolated system D a closed system 33An isentropic process is always A irreversible and adiabatic B reversible and isothermal C friction less and irreversible D reversible and adiabatic 34Work done in a free expansion process is A 0 B minimum C maximum D positive |