NIT Warangal B.tech Mechanical Stream syllabus

I want to take admission in the NIT Warangal B.tech Mechanical? Please tell me from where I can get its syllabus? Tell me about its address?

[Kiran Chandar]

The National Institute of Technology, Warangal is formerly known as Regional Engineering College. The NIT Warangal was established in the 1959.

As you say that you want to take admission in the NIT Warangal B.tech Mechanical. The Mechanical branch contains the following:

1. Thermal Engineering

2. Manufacturing Engineering

3. Computer Integrated Manufacturing

4. Machine Design

5. Automobile Engineering

6. Materials and System Engineering Design

7. Additive Manufacturing

You are also asking for the NIT Warangal B.tech Mechanical branch syllabus. Here I am uploading a file that contains the NIT Warangal B.tech Mechanical syllabus. Here I am also providing you some content of the file this is as follows:

Detailed Syllabus:
Review of Basics: Introduction to Prime Movers, Gas Turbines, Review of Basic principles – Thermodynamics, Review of Basic principles – Fluid Dynamics and Heat Transfer, Fundamentals of Rotating Machines – Energy Equation, Dimensional Analysis, Airfoil Theory.

Ideal Gas Turbine Cycles: Analysis of Ideal Gas Turbine Cycles, Simple Cycle, Regeneration Cycle, Reheat Cycle, Inter cooling Cycle.
Practical Gas Turbine Cycles: Analysis of Practical Gas Turbine Cycles, Methods of accounting for component losses, Efficiencies, change in the composition of the working fluid.

Propulsion Cycles: Jet Propulsion Cycles and their Analysis for turbojet, turboprop and turbofan engines-efficiency and specific thrust Factors Affecting Flight Performance & Methods of Thrust Augmentation.

Centrifugal Compressors: Centrifugal Compressors- Principle of Operation, T-s diagram, Energy equation, velocity triangles, types of blades. Analysis of Flow, Performance Characteristics.









Address:
National Institute of Technology,
Warangal - 506004,
A.P, INDIA
Grams: NITWGL
Phone: +91-870-2459191
FAX : +91-870-2459547

I am B.Tech Mechanical engineering students of RTU. Will you please forward me syllabus of NIT Warangal’s B.Tech Mechanical so I can compare my syllabus with it?

[Quick Sam]

As per your request, I am sharing with you the syllabus of the B.Tech mechanical course offered by the national Institute of Technology, Warangal. Take a look.

FLUID MECHANICS & HYDRAULIC MACHINES LAB

Calibration of Venturi Metre, Orifice metre (discharge measuring device in pipes)
Calibration of Orifice and mouthpiece (discharge measuring device in Tanks).
Calibration of Triangular Notch and rectangular notch (discharge measuring device in
Channels).
Measurement of Viscosity of water, SAE
10 Oil By Hazen Poiseuille method and that of gleserene by Stoke’s method.
Determination of Darcy Friction Factor, relative roughness for laminar and turbulent flows.
Determination of Manning’s and Chezy’s coefficients for smooth and rough channels by
gradually varied flow method.
Application of momentum equation for determination of coefficient of impact of jets on flat and curved blades and Pelton bucket

Determination of Energy loss in Hydraulic jump.
Computation of pressure drag coefficient for flow past a cylinder in a subsonic wind tunnel.
Performance Characteristics of single stage centrifugal pump, multi stage centrifugal pump,
Submersible pumps, and varying speed centrifugal pump.
Performance Characteristics of Pelton turbine, Francis turbine, and Kaplan turbine

DESIGN OF MACHINE ELEMENTS

Introduction: Engineering Design and classification, Basic design procedure, requirement of machine element, traditional design methods, standards and codes, selection of preferred sizes, Engineering material and its classification, Stress -strain curves, ferrous and non ferrous materials, mechanical properties of engg materials, designation of steels, heat treatment of steels, selection of materials. Manufacturing considerations and their selection, hot and cold working of metals, design for manufacture and assembly

Concept of Machine Design:
Types of loads, stresses and strain, modes of failure, Principal
stresses, theories of failure, Rakine theory, Guests theory, Von Mises theory, selection of failure theories Design of simple machine parts, design of cotter and knuckle joint.
Design of Thre aded Joints : Forms of screw threads, nomenclature, thread series, designation, power screws, and advantages over v - threads, stress in screwed threads, bolts of uniform strength, empirical relation for initial tightening, eccentrically loaded riveted joints

Design of Riveted Joints :
Types of rivet joints, rivet heads, terminology, caulking and fullering, analysis, of riveted joint, efficiency of a riveted joint, design of boiler joints and structural joints, eccentrically loaded riveted joints.
Design of Welded Joints:
Welding process, merits and demerits of welded joint over riveted joints,
Types of welded joints, weld symbols, Strength of parallel and fillet weld, strength of a welded joint - , eccentrically loaded welded joints, weld subject to bending
moment, torsional moment

NIT Warangal’s B.Tech Mechanical syllabus





For complete syllabus consider the attachment;