2023 2024 Student Forum > Management Forum > Jobs > Oil and Natural Gas Corporation Limited Mechanical Engg last year question papers

Thread: Oil and Natural Gas Corporation Limited Mechanical Engg last year question papers Reply to Thread
Your Username: Click here to log in
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Additional Options
Miscellaneous Options

Topic Review (Newest First)
18th May 2015 04:46 PM
Kiran Chandar
Re: Oil and Natural Gas Corporation Limited Mechanical Engg last year question papers

As per your request, I am giving you previous year question paper for the mechnical engineer exam conducted by the Oil and Natural Gas Corporation Limited (ONGC).

Stokes theorem connects
A) a line integral and a surface integral
B) a surface integral and a volume integral
C) a line integral and a volume integral
D) gradient of a function and its surface integral
Answer : (A)

A solar collector receiving solar radiation at the rate of 0.6 k W/m2 transforms it to the internal energy of a fluid at an overall efficiency of 50%. The fluid heated to 350 K is used to run a heat engine which rejects heat at 313 K. If the heat engine is to deliver 2.5 kW power, the minimum area of the solar collector required would be
A) 8.33m2
B) 16.66m2
C) 39.68m2
D) 79.36m2
Answer : (D)

When the temperature of a solid metal increases,
A) strength of the metal decreaes but ductility increases
B) both strength and ductility of the metal decrease
C) both strength and ductility of the metal increase
D) strength of the metal increases but ductility decreases
Answer : (A)

A company produces two types of toys: P and Q. Production time of Q is twice that of P and the company has a maximum of 2000 time units per day. The supply of raw material is just sufficient to produce 1500 toys (of any type) per day. Toy type Q requires an electric switch which is available @ 600 pieces per day only. The company makes a profit of Rs. 3 and Rs. 5 on type P and Q respectively. For maximization of profits, the daily production quantities of P and Q toys should respectively be
A) 100, 500
B) 500, 1000
C) 800, 600
D) 1000, 1000
Answer : (C)

A spherical thermocouple junction of diameter 0.706 mm is to be used for the measurement Aof temperature of a gas stream. The convective heat transfer co-efficient on the bead surface is 400 W/m2K. Thermophysical properties of thermocouple material are k = 20 W/mK, C = 400 J/kg K and r = 8500 kg/m3. If the thermocouple initially tot 30°C is placed in a hot stream of 300°C, the time taken by the bead to reach 298°C, is
A) 2.35 s
B) 4.9 s
C) 14.7 s
D) 29.4 s
Answer : (B)

In a spring-mass system, the mass is 0.1 kg and the stiffness of the spring is 1 kN/m. By introducing a damper, the frequency of oscillation is found to be 90% of the original value. What is the damping coefficient of the damper?
A) 1.2 N.s/m
B) 3.4 N.s/m
C) 8.7 N.s/m
D) 12.0 N.s/m
Answer : (C)

In a machining operation, doubling the cutting speed reduces the tool life to 1/8 of the original value. The exponent n in Taylor
A) 1/8
B) 1/4
C) 1/3
D) 1/2
Answer : (C)

In a rolling process, sheet of 25 mm thickness is rolled to 20 mm thickness. Roll is of diameter 600 mm and it rotates at 100 rpm. The roll strip contact length will be
A) 5 mm
B) 39 mm
C) 78 mm
D) 120 mm
Answer : (A)

A soldering operation was work-sampled over two days (16 hours) during which an employee soldered 108 joints. Actual working time was 90% of the total time and the performance rating was estimated to be 120 percent. If the contract provides allowance of 20 percent of the total time available, the standard time for the operation would be
A) 8 min
B) 8.9 min
C) 10 min
D) 12 min
Answer : (D)

A welding operation is time-studied during which an operator was pace-rated as 120%. The operator took, on an average, 8 minutes for producing the weld-joint. If a total of 10% allowances are allowed for this operation, the expected standard production rate of the weld-joint (in units per 8 hour day) is
A) 45
B) 50
C) 55
D) 60
Answer : (A)

In PERT analysis a critical activity has
A) maximum Float
B) zero Float
C) maximum Cost
D) minimum Cost
Answer : (B)

Environment friendly refrigerant R134a is used in the new generation domestic refrigerators. Its chemical formula is
A) CH C1 F2
B) C2 C13 F3
C) C2 C12 F4
D) C2 H2 F4
Answer : (D)


Which of the following statements is INCORRECT?

(A) Grashof’s rule states that for a planar crank-rocker four bar mechanism, the

sum of the shortest and longest link lengths cannot be less than the sum of

the remaining two link lengths.

(B) Inversions of a mechanism are created by fixing different links one at a time.

(C) Geneva mechanism is an intermittent motion device

(D) Gruebler’s criterion assumes mobility of a planar mechanism to be one.





The natural frequency of a spring-mass system on earth is ωn. The natural

frequency of this system on the moon (gmoon = gearth / 6) is

(A) ωn (B)0.408ωn (C) 0.204ωn (D) 0.167ωn


Tooth interference in an external involute spur gear pair can be reduced by

(A) decreasing center distance between gear pair

(B) decreasing module

(C) decreasing pressure angle

(D) increasing number of gear teeth


For the stability of a floating body, under the influence of gravity alone, which of

the following is TRUE?

(A) Metacentre should be below centre of gravity

(B) Metacentre should be above centre of gravity

(C) Metacentre and centre of gravity must lie on the same horizontal line

(D) Metacentre and centre of gravity must lie on the same vertical line


The maximum velocity of a one-dimensional incompressible fully developed

viscous flow, between two fixed parallel plates, is 6ms-1. The mean velocity (in

ms-1) of the flow is

(A) 2 (B) 3 (C) 4 (D) 5

A phenomenon is modeled using n dimensional variables with k primary

dimensions. The number of non-dimensional variables is

(A) k (B) n (C) n-k (D) n+k



A turbo-charged four-stroke direct injection diesel engine has a displacement

volume of 0.0259m3 (25.9litres) . The engine has an output of 950kW at

2200rpm. The mean effective pressure in MPa is closest to

(A) 2 (B) 1 (C) 0.2 (D) 0.1


One kilogram of water at room temperature is brought into contact with a high

temperature thermal reservoir. The entropy change of the universe is

(A) equal to entropy change of the reservoir

(B) equal to entropy change of water

(C) equal to zero

(D) always positive


A hydraulic turbine develops 1000kW power for a head of 40m. If the head is

reduced to 20m, the power developed (in kW) is

(A) 177 (B) 354 (C) 500 (D) 707


The material property which depends only on the basic crystal structure is

(A) fatigue strength (B) work hardening

(C) fracture strength (D) elastic constant


In a gating system, the ratio 1:2:4 represents

(A) sprue base area: runner area: ingate area

(B) pouring basin area: ingate area: runner area

(C) sprue base area: ingate area: casting area

(D) runner area: ingate area: casting area
A shaft has a dimension, 0.009

35 0.025 −− φ . The respective values of fundamental deviation

and tolerance are

(A) −0.025, ± 0.008 (B) −0.025,0.016

(C) −0.009, ±0.008 (D) −0.009,0.016


In a CNC program block, N002 G02 G91 X40 Z40…, G02 AND G91 refer to

(A) circular interpolation in counterclockwise direction and incremental dimension

(B) circular interpolation in counterclockwise direction and absolute dimension

(C) circular interpolation in clockwise direction and incremental dimension

(D) circular interpolation in clockwise direction and absolute dimension


The demand and forecast for February are 12000 and 10275, respectively. Using

single exponential smoothening method (smoothening coefficient = 0.25),

forecast for the month of March is

(A) 431 (B) 9587 (C) 10706 (D) 11000


Little’s law is relationship between

(A) stock level and lead time in an inventory system

(B) waiting time and length of the queue in a queuing system

(C) number of machines and job due dates in a scheduling problem

(D) uncertainty in the activity time and project completion time


Vehicle manufacturing assembly line is an example of

(A) product layout (B) process layout (C) manual layout (D) fixed layout

Simplex method of solving linear programming problem uses

(A) all the points in the feasible region

(B) only the corner points of the feasible region

(C) intermediate points within the infeasible region

(D) only the interior points in the feasible region.


Torque exerted on a flywheel over a cycle is listed in the table. Flywheel energy

(in J per unit cycle) using Simpson’s rule is

Angle (degree) 0 60 120 180 240 300 360

Torque (Nm) 0 1066 -323 0 323 -355 0

(A) 542 (B) 993 (C) 1444 (D) 1986
29th July 2014 03:56 PM
Kiran Chandar
Re: Oil and Natural Gas Corporation Limited Mechanical Engg last year question papers

As you want to get the Oil and Natural Gas Corporation Limited Mechanical Engg last year question papers so here it is for you:

1 During the execution of a CNC part program block NO20 GO2 X45.0 Y25.0 R5.0 the type of tool motion will be
A) circular Interpolation — clockwise
B) circular Interpolation — counterclockwise
C) linear Interpolation
D) rapid feed
Answer : (A)

2 A component can be produced by any of the four processes I, II, III and IV. Process I has a fixed cost ofRs. 20 and variable cost of Rs. 3 per piece. Process II has a fixed cost Rs. 50 and variable cost of Re. 1 per piece. Process III has a fixed cost of Rs. 40 and variable cost of Rs. 2 per piece. Process IV has a fixed cost of Rs. 10 and variable cost of Rs. 4 per piece. If the company wishes to produce 100 pieces of the component, from economic point of view it should choose
A) Process I
B) Process II
C) Process III
D) Process IV
Answer : (B)

3 In an interchangeable assembly, shafts of size 25.000+0.040mm mate with holes of size 25.000+0.020 mm. The maximum possible clearance in the assembly will be
A) 10 microns
B) 20 microns
C) 30 microns
D) 60 microns
Answer : (D)

4 A company has two factories S1, S2 and two warehouses D1, D2. The supplies from S1 and S2 are 50 and 40 units respectively. Warehouse D1 requires a minimum of 20 units and a maximum of 40 units. Warehouse D2 requires a minimum of 20 units and, over and above, it can take as much as can be supplied. A balanced transportation problem is to be formulated for the above situation. The number of supply points, the number of demand points, and the total supply (or total demand) in the balanced transportation problem respectively are
A) 2, 4, 90
B) 2, 4, 110
C) 3, 4, 90
D) 3, 4, 110
Answer : (C)

5 An incompressible fluid (kinematic viscosity, 7.4 x 10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is
A) 0.651 x 10-3
B) 0.651
C) 6.51
D) 0.651 x 103
Answer : (B)

6 The tool of an NC machine has to move along a circular arc from (5,5) to (10,10) while performing an operation. The centre of the arc is at (10,5). Which one of the following NC tool path commands performs the above mentioned operation?
A) N010 G02 X10 Y10 X5 Y5 R5
B) N010 G03 X10 Y10 X5 Y5 R5
C) N010 G01 X5 Y5 X10 Y10 R5
D) N010 G02 X5 Y5 X10 Y10 R5
Answer : (D)

7 During a Morse test on a 4 cylinder engine, the following measurements of brake power were taken at constant speed.
All cylinders firing 3037 kW
Number 1 cylinder not firing 2102 kW
Number 2 cylinder not firing 2102 kW
Number 3 cylinder not firing 2100 kW
Number 4 cylinder not firing 2098 kW
The mechanical efficiency of the engine is
A) 91.53%
B) 85.07%
C) 81.07%
D) 61.22%
Answer : (C)

8 In terms of theoretical stress concentration factor (Kt) and fatigue stress concentration factor (Kf ), the notch sensitivity ‘q’ is expressed as
A) (Kf -1) (Kt -1)
B) (Kf -1) (Kt +1)
C) (Kt -1) (Kf -1)
D) (Kf +1) (Kt +1)
Answer : (A)

9 Starting from x0 = 1, one step of Newton-Raphson method in solving the equation x3 + 3x -7 = 0 gives the next value (x1) as
A) x1 = 0.5
B) x1= 1.406
C) x1= 1.5
D) x1 = 2
Answer : (C)

10 The S-N curve for steel becomes asymptotic nearly at
A) 103 cycles
B) 104 cycles
C) 10 6 cycles
D) 10 9 cycles
Answer : (C)

11. In PERT analysis a critical activity has
A) maximum Float
B) zero Float
C) maximum Cost
D) minimum Cost
Answer : (B)

12 Environment friendly refrigerant R134a is used inthe new generation domestic refrigerators. Itschemical formula is
A) CH C1 F2
B) C2 C13 F3
C) C2 C12 F4
D) C2 H2 F4
Answer : (D)

13 A solid cylinder (surface 2) is located at the centreof a hollow sphere (surface 1). The diameter of the sphere is 1m, while the cylinder has a diameter and length of 0.5 m each. The radiation configuration factor F11 is
A) 0.375
B) 0.625
C) 0.75
D) 1
Answer : (C)

14 For a fluid flow through a divergent pipe of length L having inlet and outlet radii of R1 and R2 respectively and a constant flow rate of Q, assuming the velocity to be axial and uniform at any cross-section, the acceleration at the exit is
A) 2Q(R1 - R2) p LR23
B) 2Q2 (R1 - R2) p LR23
C) 2Q2 (R1 - R2) p2LR25
D) 2Q2 (R2 - R1) p2LR25
Answer : (C)

15 An incompressible fluid (kinematic viscosity, 7.4 x 10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is
A) 0.651 x 10-3
B) 0.651
C) 6.51
D) 0.651 x 103
Answer : (B)

16 The tool of an NC machine has to move along a circular arc from (5,5) to (10,10) while performing an operation. The centre of the arc is at (10,5). Which one of the following NC tool path commands performs the above mentioned operation?
A) N010 G02 X10 Y10 X5 Y5 R5
B) N010 G03 X10 Y10 X5 Y5 R5
C) N010 G01 X5 Y5 X10 Y10 R5
D) N010 G02 X5 Y5 X10 Y10 R5
Answer : (D)

17 During a Morse test on a 4 cylinder engine, the following measurements of brake power were taken at constant speed.
All cylinders firing 3037 kW
Number 1 cylinder not firing 2102 kW
Number 2 cylinder not firing 2102 kW
Number 3 cylinder not firing 2100 kW
Number 4 cylinder not firing 2098 kW
The mechanical efficiency of the engine is
A) 91.53%
B) 85.07%
C) 81.07%
D) 61.22%
Answer : (C)

18 In terms of theoretical stress concentration factor(Kt) and fatigue stress concentration factor (Kf ), the notch sensitivity ‘q’ is expressed as
A) (Kf -1) (Kt -1)
B) (Kf -1) (Kt +1)
C) (Kt -1) (Kf -1)
D) (Kf +1) (Kt +1)
Answer : (A)

19 Starting from x0 = 1, one step of Newton-Raphson method in solving the equation x3 + 3x -7 = 0 gives the next value (x1) as
A) x1 = 0.5
B) x1= 1.406
C) x1= 1.5
D) x1 = 2
Answer : (C)

20 A maintenance service facility has Poisson arrival rates, negative exponential service time and operates on a ‘first come first served’ queue discipline. Break downs occur on an average of 3 per day with a range of zero to eight. The maintenance crew can service an average of 6 machines per day with a range of zero to seven. The mean waiting time for an item to be serviced would be
A) 16 day
B) 13 day
C) 1 day
D) 3 days
Answer : (A)

21 The S-N curve for steel becomes asymptotic nearly at
A) 103 cycles
B) 104 cycles
C) 106 cycles
D) 109 cycles
Answer : (C)

22 In a rolling process, sheet of 25 mm thickness is rolled to 20 mm thickness. Roll is of diameter 600 mm and it rotates at 100 rpm. The roll strip contact length will be
A) 5 mm
B) 39 mm
C) 78mm
D) 120mm
Answer : (A)

23 Water at 42°C is sprayed into a stream of air at atmospheric pressure, dry bulb temperature of 40°C and a wet bulb temperature of 20°C. The air leaving the spray humidifier is not saturated. Which of the following statements is true?
A) Air gets cooled and humidified
B) Air gets heated and humidified
C) Air gets heated and dehumidified
D) Air gets cooled and dehumidified
Answer : (B)

24 The angle between two unit-magnitude coplanar vectors P(0.866, 0.500,0) and Q(0.259, 0.966,0) will be
A) 0°
B) -30°
C) 45°
D) 60°
Answer : (C)

25 A lot has 10% defective items. Ten items are chosen randomly from this lot. The probability that exactly 2 of the chosen items are defective is
A) 0.0036
B) 0.1937
C) 0.2234
D) 0.3874
Answer : (B)
29th July 2014 08:33 AM
Unregistered
Oil and Natural Gas Corporation Limited Mechanical Engg last year question papers

Will you please share with me the Oil and Natural Gas Corporation Limited Mechanical Engg last year question papers?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT +5. The time now is 03:25 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4