2023 2024 Student Forum > Management Forum > Main Forum

 
  #2  
13th May 2018, 12:32 PM
Unregistered
Guest
 
Re: Mahamaya Technical University Subject Codes

Hii sir, I Wants to get the Syllabus of the B.tech VIII Sem Civil Engineering Subject Code NCE-701 Design of Steel Structures of the Dr. A.P.J. Abdul Kalam Technical University Uttar Pradesh ?
  #3  
13th May 2018, 12:32 PM
Super Moderator
 
Join Date: Aug 2012
Re: Mahamaya Technical University Subject Codes

As you Asking for the Syllabus of the B.tech VIII Sem Civil Engineering Subject Code NCE-701 Design of Steel Structures of the Dr. A.P.J. Abdul Kalam Technical University Uttar Pradesh is given below

Subject Code NCE-701 Design of Steel Structures

Unit ‐ 1

General Considerations
Introduction, Advantages of Steel as a Structural. Material, Disadvantages of Steel as a Structural Material, Structural Steel, Stress‐Strain Curve for Mild Steel, Rolled Steel Sections, Convention for Member Axes, Loads, Dead Load, Live Loads, Environmental Loads, Seismic Forces, Snow and Rain Loads, Erection Loads, Basis for Design, Design Philosophies, Local Buckling of Plate Elements.

Introduction to Limit State Design
Introduction, Limit States for Steel Design, Limit States of Strength, Limit States of Serviceability, Actions (Loads), Probabilistic Basis for Design, Design Criteria8

Unit ‐2
Simple Connections‐Riveted, Bolted and Pinned Connections
Introduction, Riveted Connections, Patterns of Riveted Joints, Bolted Connections, Types of Bolts, Types of Bolted Joints, Load Transfer Mechanism, Failure of Bolted Joints, Specification for Bolted Joints,

Bearing‐Type Connections, Prying Action, Tensile Strength of Plate, Efficiency of the Joint, Combined

Shear and Tension, Slip‐Critical Connections, Combined Shear and Tension for Slip‐Critical Connections, Working Load Design, Design of eccentric bolted connections . Simple Welded Connections

Introduction, Types, Symbols, Welding Process, Weld Defects, Inspection of Welds, Assumptions in the Analysis of Welded Joints, Design of Groove Welds, Design of Fillet Welds, Fillet Weld Applied to the Edge of A Plate Or Section, Fillet Weld for Truss Members, Design of Intermittent Fillet Welds, Plug and
Slot Welds, Stresses Due To Individual Forces, Combination of Stresses, Failure of Welds, Distortion of Welded Parts, Fillet Weld Vs Butt Weld, Welded Jointed Vs Bolted and Riveted Joints, Design of eccentric welded connections, Working Load Design. 8

Unit 3
Tension Members
Introduction, Types of Tension Members, Net Sectional Area, Effective Net Area, Types of Failure, Design Strength of Tension Members, Slenderness Ratio (λ), Displacement, Design of Tension Member, Lug Angles, Splices, Gusset Plate, Working Load Design. 8

Unit 4
Compression Members
Introduction, Effective Length, Slenderness Ratio (λ), Types of Sections, Types of Buckling, Classification of Cross Sections, Column Formula, Design Strength, Design of Axially Loaded Compression Members, Built‐Up Columns (Latticed Columns), Lacing, Batten, Compression Member Composed of Two
Components Back‐to‐Back, Splices, Design of Column Bases. 8

Unit 5
Beams
Introduction, Types of Sections, Behaviour of Beam in Flexure, Section Classification, Lateral Stability of Beams, Lateral‐Torsional Buckling, Bending Strength of Beams, Laterally Supported Beams, Laterally Unsupported Beams, Shear Strength of Beams, Web Buckling, Bearing Strength, Web Crippling,
Deflection, Design Procedure of Rolled Beams, Built‐Up Beams (Plated Beams), Purlins, Beam Bearing Plates, Effect of Holes in Beam, Introduction to Plate Girder , Introduction toGantry Girder

For more Information you may Contact to the Dr. A.P.J. Abdul Kalam Technical University Uttar Pradesh the Contact Details Are given below

Contact Details
Dr. A.P.J. Abdul Kalam Technical University
Address: C-22, C Block, C Block, Phase 2, Industrial Area, Sector 62, Noida, Uttar Pradesh 201301
Phone: 0120 240 0112


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 05:33 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4