2023 2024 Student Forum > Management Forum > Main Forum

 
  #1  
18th December 2014, 09:28 AM
Unregistered
Guest
 
IIIT Hyderabad M.TECH Electronics and Communication Engineering Exam Paper

Will you please provide the M.Tech ECE Exam question paper of
IIIT Hyderabad?
Similar Threads
Thread
Government jobs after B.Tech Electronics and Communication Engineering
Career after the course of B.Tech Electronics and Communication Engineering
After B.Tech Electronics and Communication Engineering government jobs exams
After B tech Electronics & communication Engineering Jobs in software
Government jobs after B.Tech in Electronics and Communication Engineering
M.Tech CSE Entrance Exam Paper of IIIT Hyderabad
Tamilnadu B.Tech. Electronics and Communication Engineering Colleges
M.Tech (Automobile Engineering) after B.Tech) Electronics and Communication )
Government Exams after B.Tech Electronics and Communication Engineering
Electronics and Communication Engineering 6th Semester Old question paper
Puducherry B.Tech. Electronics and Communication Engineering Colleges
Courses after B.Tech Electronics and Communication Engineering
M.Tech Automobile Engineering after B.Tech Electronics and Communication
IIIT Hyderabad M.Tech ECE Entrance Exam Question Paper
Career after the course of B.Tech Electronics & Communication Engineering
Previous Paper for BEL PE Electronics and Communication Engineering
M.Tech. Electronics and Communication Engineering Colleges
Branch which is better for M.Tech for Electronics & Communication Engineering
Scope after the course of B.Tech Electronics and Communication Engineering
Career after B.Tech Electronics and Communication Engineering
  #2  
18th December 2014, 09:58 AM
Super Moderator
 
Join Date: Apr 2013
Re: IIIT Hyderabad M.TECH Electronics and Communication Engineering Exam Paper

Here is the list of few questions of M.Tech ECE Exam question paper of IIIT Hyderabad which you are looking for .


1 In an abrupt p-n junction, the doping concentrations on the p-side and n-side are NA = 9x 1016/cm3 and ND = 1 x 1016/cm3 respectively. The p-n junction is reverse biased and the total depletion width is 3 m m. The depletion width on the p-side is A) 2.7 mm B) 0.3 mm. C) 2.25 mm D) 0.75 mm Answer : (B)

2 A system has poles at 0.01 Hz, 1 Hz and 80 Hz; zeros at 5 Hz, 100 Hz and 200 Hz. The approximate phase of the system-response at 20 Hz is A) - 90° B) 0° C) 90° D) - 180° Answer : (A) A D V E R T I S E M E N T

3 A parallel plate air-filled capacitor has plate area of l0-4 m2 and plate separation of 10-3 m. It is connected to a 0.5 V, 3.6 GHz source. The magnitude of the displacement current is (e0 = 1/36p x 10-9 F/m) A) 10 mA B) 100 mA C) 10 A D) 1.59 mA Answer : (A)

4 A master-slave flip-flop has the characteristic that A) change in the input immediately reflected in the output B) change in the output occurs when the state of the master is affected C) change in the output occurs when the state of the slave is affected D) both the master and the slave states are affected at the same time Answer : (C)

5 Noise with uniform power spectral density of N0W/Hz is passed through a filter H (w) = 2 exp(-jwtd) followed by an ideal low pass filter of bandwidth BHz. The output noise power in Watts is A) 2N0B
B) 4N0B C) eN0B D) 16 N0B Answer : (B)

6 The phase velocity of an electromagnetic wave propagating in a hollow metallic rectangular waveguide in the TE10 mode is A)equal to its group velocity B) less than the velocity of light in free space C) equal to the velocity of light in free space D) greater than the velocity of light in free space Answer : (D)

7 The cascade amplifier is a multistage configuration of A) CC-CB B) CE-CB C) CB-CC D) CE-CC Answer : (B)

8 The bandgap of Silicon at room temperature is A) 1.3 eV B) 0.7 eV C) 1.1 eV D) 1.4 eV Answer : (C)


9 Consider a lossless antenna with a directive gain of +6dB. If 1 mW of power is fed to it the total power radiated by the antenna will be A) 4 mW B) 1 mW C) 7 mW D) 1/4 mW Answer : (A)

10 In a PCM system, if the code word length is increased from 6 to 8 bits, the signal to quantization noise ratio improves by the factor A) 8/6 B) 12 C) 16 D) 8 Answer : (C)

11 An AM signal is detected using an envelope detector The carrier frequency and modulating signal frequency are 1 MHz and 2 kHz respectively. An appropriate value for the time constant of the envelope detector is A) 500 msec B) 20 msec C) 0.2 msec D) 1 msec Answer : (B)

12 For the polynomial P(s) = s5 + s4 + 2s3 + 2s2 + 3s + 15, the number of roots which lie in the right half of the s-plane is
A) 4 B) 2 C) 3 D) 1 Answer : (B)

13 A device with input x(t) and output y(t) is characterized by: y(t) = x2(t). An FM signal with frequency deviation of 90 kHz and modulating signal bandwidth of 5 kHz is applied to this device. The bandwidth of the output signal is A) 370 kHz B) 190 kHz C) 380kHz D) 95kHz Answer : (C)

14 Consider the following statements S1 and S2. S1: The b of a bipolar transistor reduces if the base width is increased. S2: The b of a bipolar transistor increases if the doping concentration in the base is increased. Which one of the following is correct? A) S1 is FALSE and S2 is TRUE B) Both S1 and S2 are TRUE C) Both S1 and S2 are FALSE D) S1 is TRUE and S2 is FALSE Answer : (D)

15 In a PCM system, if the code word length is increased from 6 to 8 bits, the signal to quantization noise ratio improves by the factor A) 8/6 B) 12 C) 16 D) 8 Answer : (C)


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 02:17 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4