Dote mba

Hii Guys , Here I am Searching For Previous year Directorate of Technical Education, Chennai (DOTE Chennai) Of The Institution Of Engineers India M.B.A 7th Semester Exam paper , Can you please Provide me Same ?

[Pathak]

Friend On your Demanding Here I am Providing Previous year Directorate of Technical Education, Chennai (DOTE Chennai) M.B.A 7th Semester Exam Paper :

Time : Three Hours

Maximum Marks : 100

Ans All Ques.

PART - A 10 x two = 20 Marks

1. Sketch the stress-strain diagram for a ductile specimen and indicate its salient features.

2. Indicate the kind of fit used in the assembly of bush in the big-end of the connecting rod of an automobile.

3. describe 'endurance limit' in design

4. Indicate the kind of fit specified by 120 H7 p6 in a drawing.

5. Mention any 2 desirable properties of the material used in an automobile piston.

6. Sketch and indicate the salient parts of a flange coupling.

7. Mention the stresses induced in a taper key used in a coupling.

8. What is a 'bearing characteristic number'.

9. Mention the names of any 4 theories of failure.

10. describe 'coefficient of fluctuation of speed' in a flywheel.

PART – B five x 16 = 80 Marks

11. i) A load of five KN is to be raised by means of a steel wire. obtain the minimum diameter required, if the permissible stress in the wire is not to exceed 100 N /mm2 (4 Marks)

ii) A square bar of 20 mm x 20 mm insection is subjected to a bending moment of 1000 Nmm. compute the stress induced in the top and bottom fibres of the bar. What will be stress in the above fibres, if the bar is additionally acted upon by a tensile stress of 50 N/mm2 along the axis. (6Marks)

iii) A circular shaft is to transmit a torque of 500 Nmm at a speed of 1000 rpm. obtain out the diameter of the shaft, if the permissible shear stress in the shaft material is 70 N/mm2. (6 Marks)

12.a) A shaft is supported by 2 bearing organizes one m apart, A 600 mm diameter pulley is mounted at a distance of 300 mm to the right of the left hand bearing and this drives a pulley directly beneath it with the help of a belt having maximum tension of 2.25 kN. a different pulley of 400mm diameter is placed 200 mm to the left of the right hand bearing and is driven with the help of an electric motor and a belt, horizontallyto the right. The angle of contact for both the pulley is 1800 and the coefficient of friction is 0.24. Design the diameter of the solid shaft, allowing a working stress of 60 N/mm2 in tension and 40 N/mm2 in shear for the material of the shaft. presume the torque input & torque output are equal.

OR

12.b) A bar of circular cross part is subjected to alternating tensile forcesvarying from a minimum of 200 kN to maximum of 500 kN. It is to be manufactured from a material with an ultimate tensile strength of 90 MPa and an endurance limit of 70 MPa. Determine the diameter of the bar using safety factors of 3.5 in ultimate tensile strength and four in endurance limit strength and stress concentration factor of 1.65 for fatigued load. Use Goodman relation for the basis of design.

13.a) A circular rod 45 mm diameter and 210 mm long is welded to a steelplate with axis of the rod perpendicular to the plate. The rod is subjected to a load of 10 kN at the free end, the direction of the load being perpendicular to the axis of therod. The material of the plate & the rod are Mild Steel. Determine the size of the weld to withstand the loading.

OR

13.b) An electric motor weighting five kN is to be lifted by eye-bolt, which has been screwed into the body of the motor. describe the eye-bolt, assuming suitable proportions, if the permissible stresses for the bolt material are 60 MPa, 30 Mpa and 80 MPa in tension, shear and crushing respectively.

14.a) choose a deep groove ball bearing for a radial load of 4000 N and an axial load of 5000 N, operating at speed of 1600 rpm for an avg. life of five years at 10 hours per day. presume uniform and steady load.

OR

14. b) Design a connecting rod for a petrol engine for the subsequent data:

Diameter of the piston = 68 mm

Stroke length = 80 mm

Length of connecting rod = 160 mm

Maximum explosion pressure = 3.5 N/ mm2

Mass of reciprocating parts = 2.5 kg

Speed = 4000 rpm

Compression ratio = eight :1

15.a) A helical compression spring of the exhaust valve mechanism is initially compressed with a pre-load of 375 N. When the spring is further compression and the valve is fully opened, the torsional shear stress in the spring wire should not exceed 750 N/mm2. Due to Space limitations, the outer diameter of thespring is not exceed 42 mm. The spring is to be designed for minimumweight. compute the wire diameter and the mean coil diameter of the spring.

OR

15.b) A semi-elliptic leaf spring consists of 2 extra full-length leaves and 6 graduated length leaves, including the master leaf. Eachleaf is 7.5 mm thick and 50 mm wide. The center-to-centre distance ranging from the 2 eyes is 1m.The leaves are pre-stressed in such a way that when the load is maximum, the stresses induced in all the leaves are equal to 350 N / mm2. Determine themaximum force that the spring can withstand.


Address :

The Institution Of Engineers India
Circle-I Office, PWD Campus, Staff Cooperative Society
63, 3rd Floor
Netaji Subhash Chandra Bose Salai ( Gingee Salai )
Puducherry, 605001