2023 2024 Student Forum > Management Forum > Main Forum

 
  #2  
3rd June 2016, 11:43 AM
Super Moderator
 
Join Date: Mar 2013
Re: Is BSNL TTA A Good Job

Bharat Sanchar Nigam Limited is a Public Service Undertaking Company so its obvious that getting a job in PSU on any post is a good career opportunities therefore Telecom Technical Assistant job is good too

A Telecom Technical Assistant is tasked with the function of maintenance in new areas of telecom technology.

TTA in BSNL can be categorized into two categories


•TTA (switching)

•TTA (transmission)

A technical assistant in BSNL works under the supervision of JTO and SDE.



Eligibility Criteria


Academic Qualification

Three Years Engineering Diploma in

- Telecommunications Engineering

- Electronics Engineering

- Electrical Engineering

- Radio Engineering

- Computer Engineering

- Instruments Technology

- Information Technology.

M.Sc. (Electronics) from a recognized institution /university.


Age Limit:-

Candidates aged between 18 and 27 years of age are eligible to apply.

Age Relaxation:-

•For Scheduled Castes & Scheduled Tribes up to 5 years

•For OBC Candidates up to 3 years




Paper Pattern:-

There shall be only one Paper of multiple choice objective type of three hours duration.

Part- I - General Ability Test - 20 marks

Part- II Basic Engineering - 90 marks

Part- III Specialization - 90 marks

Total number of Questions in the paper would be 200 and each question shall carry one mark.


Syllabus

PART-I: GENERAL ABILITY TEST - 20 MARKS


The candidate’s comprehension and understanding of General
English shall be tested through simple exercise such as provision of antonyms and synonyms, fill in the blanks and multiple-choice exercise etc. This shall also include questions on current events, general knowledge and such matters of everyday observation and experiences as may be expected of Diploma holder.


PART-II: BASIC ENGINEERING - 90 MARKS

1. Applied mathematics: Co-ordinate Geometry: Vector Algebra;Matrix and Determinant: Differential Calculus; Integral Calculus: Differential equation of second order: Fourier series; Laplace Transform; Complex Number, Partial Differentiation.

2.Applied Physics: Measurement-Units and Dimension; Waves, Acoustics, Ultrasonic; Light; Laser and its Application, Atomic Structure and Energy Levels.

3. Basic Electricity:Electrostatics, Coulomb’s law, Electric field, Gauss’s theorem, concept of potential difference; concept of capacitance and capacitors; Ohm’s law power and energy, Kirchoff’s voltage, current laws and their applications in simple DC circuits, Basic Magnetism; Electro Magnetism; Electromagnetic Induction; Concept of alternating voltage & current; Cells and Batteries; Voltage and Current Sources; Thevenin’stheorem, Norton’s theorem and their applications.

4. Electronics Devices and Circuits: Classification of materials into conductor,semi conductor, insulator etc, electrical properties, magnetic materials, various types of relays, switches and connectors, Conventional representation of electric and electronic circuits elements. Active and passive components; semi conductor Physics, Semiconductor Diode; Bipolar transistor & their circuits; Transistor Biasing Stabilization of operating point; Single stage transistor amplifier, field effect transistor, Mosfet circuits applications. Multistage Transistor Amplifier, Transistor Audio Power Amplifiers; Feedback in Amplifier, Sinusoidal Oscillators; Tuned Voltage Amplifiers; Opto Electronics Devices and their applications; Operational Amplifier, Wave shaping and switiching circuits. Block diagram of I.C. Timer(such as 555) and its working,Motivation circuits;Time Base Circuits ,Thyristory and UJT;Regulated Power Supply.

Digital Techniques:-

Applications and advantages of digital systems; number system (binary and hexadecimal); Logic Gates; Logic Simplication, Codes and Parity; Arithmetic Circuits; Decoders, Display Devices and Associated Circuits Multiplexers and De-multiplexers; Latches and Flip Flops; Counters; Shift Registers; Memories; A/D andD/A converters.


PART-III: SPECIALIZATION -90 MARKS

Electrical: 3 phases vs. single-phase supply, Star Delta connections, relation between phase & line voltage power factor and their measurements; construction and principles of working of various types of electrical measuring instruments. All types of motor and generator-AC & DC transformers, starters, rectifiers, inverters, battery charges, batteries, servo and stepper motors, contactor control circuits, switchgear, relays, protection devices & schemes, substation, protective relaying, circuits breaker, generator protection, transformer protection, feeder & lightening protection, feeder & bus bar protection, lightening arrestor, earthing, voltage stabilizer & regulators, power control devices &circuits, phase controlled rectifiers, inverters, choppers dual converters, cyclo- converters power electronics application in control of drivers, refrigeration & air conditioning.

Communication:-

Modulation and demodulation- principles and operation of various types of AM, FM and PM modulators/demodulators; pulse modulation-TDM, PAM, PPM, PWM, Multiplexing, Principles and applications of PCM. Introduction of Basic block diagram of digital and data communication systems, Coding error detection and correction techniques; Digital Modulation Techniques- ASK, ICW, FSK, PSK; Characteristics/working of data transmission circuits; UART, USART; Modems; Protocols and their functions, brief idea of ISDN interfaces, local areas Network, Carrier Telephony – Features of carrier telephone system. Microwave Engineering; Mecrowave Devices; Wave- guides; Microwave Components; Microwave Antennas; Microwave Communication Systems- Block diagram & working principal’s of microwave communication link.

Network, Filters and Transmission Lines:

Two port network,Attenuators,Filters,Transmission Lines and their applications,characteristic impedence of line,concept of refection and standing waves on a transmission line,Transmission line equation,Principles of impedance matching,Bandwidth consideration of a transmission line.

Instruments and Measurements:- Specification of Instruments-accuracy,precision,sensitivity,resolution range,Errors in measurements and loading effect,principles of voltage,current and resistance measurements,Transducers,measurement of displacement & strain , forces & torque measuring devices, pressure measuring devices,flow measuring devices,power control devices and circuits.Types of AC milli voltmeters-Amplifier rectifier and rectifier amplifier,Block diagram explanation of a basic CRO and a triggered sweep oscilloscope,front panel controls,impedance Bridges and Q-Meters. Principles of working and specifications of logic probes,signature analyzer and logic analyzer,signal generator, distortion factor meters,spectrum analyzer.

Control Systems:- Basic elements of control system,open and closed loop system, concept of feedback, Block diagram of control system,Time lag,hysterisis, linearity concepts,Self-regulating and non-self regulating control systems,Transfer function of simple control components,single feedback configuration. Time response of systems.Stability Analysis Characteristics equation,Routh’s table,Nyquist criterion ,Relative stability,phase margin and gain margin. Routh Hurwitz critierion,root locus techniques,Bode plot, Power plot ,Gain margin and phase margin.

Microprocessors:-


Typical organization of a microcomputer system & functions of its various blocks, Architecture of a Microprocessors, Memories and I/O interfacing ,Brief idea of M/C assembly languages ,Machines & Mnemonic codes, Instruction format and Addressing mode,concept of instruction set ,programming excercises in assembly language ,concept of interrupt, Data transfer techniques-sync data transfer, interrupt driven data transfer,DMA ,serial out put data, serial input data.

Computer:-

Computer and its working,types of computers,familiarization with DOS and Windows concept of file,directory,folder,Number systems,Data representation,Programming-Elements of a high level programming language,PASCAL,C:Use of basic data structures,Fundamentals of computer architecture,Processor design,Control unit design,memory organization,I/O system organization,Microprocessors- microprocessor architecture,instruction set and simple assembly level programming,Microprocessors based system design: typical examples,Personal computers and their typical uses,data communication principles,types and working principles of modems,Network principles,OSI model,functions of data link layer and network layer,networking componets, communications protocols a-X.25,TCP/IP. Database Management system -Basic concepts, entity relationship model, relational model, DBMS based on relational mode.


Tags
age limit

Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 09:32 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4