2023 2024 Student Forum > Management Forum > Main Forum

 
  #2  
18th August 2014, 12:28 PM
Super Moderator
 
Join Date: Apr 2013
Re: Bharat Heavy Electricals Limited entrance exam previous year question papers

As you want to get the Bharat Heavy Electricals Limited entrance exam previous year question papers so here it is for you:

When a inductive coil connected to a 200 V, 50Hz ac supply with 10A current flowing through it dissipates 1000 watts then which of the following will have least value in ohms

a.) Resistanceb.) Reactancec.) Impedance d.) None

Oscillator crystal are made of –

a.) Silicon

b.) Germanium

c.) Quartz

d.) None

For small size, high frequency coils, the most common core material is-a. )Airb. )Ferrite c.) Powdered ion
d.) Steel
If we have a parallel plate capacitor of plate area ‘A’ and plate separatoin t and having a capacity C and a metallic plate r of area A and of negligible thickness is introduced in the capacitor at a distance from either of the two plates as shown in the given figure then the capacity of the capacitor will become –

a.)

b.) C

c.) 2C

d.) 4C

A superconductor is a –

a.) A material showing perfect conductivity and Meissner effect below a critical temperature

b.) A conductor having zero resistance

c.) A perfect conductor with highest di-magnetic susceptibility

d.) A perfect conductor which becomes resistance when the current density through it exceeds a critical value

When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF capacitor then the self capacitance of the inductor would be –

a) 8.05 pF

b) 10.05pF

c.) 16.01pF

d.) 20.01pF

Sparking occur when a load is switched off because the circuit has high –

a.) Inductance

b.) Capacitance

c.) Resistance

d.) None

Sparking between contacts can be reduced by inserting a –

a.) Resistance in the line

b.) Capacitor in series with contacts

c.) Capacitor in parallel with contacts

d.) None

RF amplifier of an A.M. receiver is normally biased in –

a.) Class ‘A’

b.) Class ‘b’

c.) Class ‘C’

d.) None

The value of gate voltage for the operation of enhancement of only N channel MOSFET has to be –

a.) High positive

b.) High negative

c.) Low positive

d.) Zero

The input gate current of a FET is –

a.) a few microamperes

b.) negligibly small

c.) a few milliamperes

d.) a few amperes

In the following fig. with R = 30k, the value of current through 2 K resistor is –

a.) 25 mA
b.) 40 mA
c.) 25/16 mA
d.) 10 mA

A step recovery diode –

a.) has on extremely short recovery time

b.) conducts equally well in both directions

c.) is mainly used as a harmonic generator

d.) is an ideal rectifiers of high frequency signals

In order to get maximum undistorted output signal from CE amplifier with VCC 10V, the value of VCE (Q) should be approximately-

a.) 0.1V

b.) 5V

c.) 10V

d) V

In a FET the electrode, which corresponds to collector in bipolar transistor, is –

a.) source

b.) drain

c.) gate

d.) none

The device which acts like an NPN and a PNP transistor connected base to base and emitter to collector is –a.) Triacb.) UJT c.) Diac
d.) SCR
A typical optical fibre has –

a.) High refractive index core and low refractive index cladding

b.) Low refractive index core and high refractive index cladding

c.) Both a and b

d.) None

In the following figure circuit diagram of an op-amp based is shown. The ratio is equal to –

a.) 9

b.) 11

c.) 10

d.) 21

When a loud speaker is connected across the terminals A and B of the network shown in the fig. then its impedance to obtain maximum power dissipation in it will be – a.) 3 – j1 b.) 3 + j9
c.) 7.5 + j 2.5
d.) 7.5 – j 2.5
In the lattice network, the value of R for the maximum power transfer to the load – a.) 5 b.) 6.5
c.) 8
d.) 9
For a lossy transmission line short circuited at the receiving end, the input impedance is given by (Z0 is the characteristic impedance, Ö is the propagation constant and l is the length of the line-a.) Z0 cot h Ölb.) Z0 cot Öl c.) Z0 tan h.Ö l
d.) Z0 tan Öl
The approximate thickness of the radome wall should be –a.) lb.) l/4 c.) l/2
d.) l/8
A relatively permanent information is stored in

a. ) ROM

b.) RAM

c.) PROM

d.) Volatile memory

The rise time of the RC network shown in the given figure is approximately equal to – b.) RC
c.) 2RC
d.) 4RC
If in the network shown in the fig. initially a steady state is attained by closing the switch ‘s’ and then if the switch is opened at t = 0, then the current i(t) through the inductor will be – a.) cos50tA b.) 2A
c.) 2cos100tA
d.) 2sin50tA
When the p network of figure – I and T-network of figure – II are equivalent then the values of R1, R2 and R3 will be respectively – a) 9W, 6W and 6W b.) 6W, 6W and 9W
c.) 9W, 6W and 9W
d.) 6W, 9W and 6W
When the impedance matrices of a two port networks are given by and , then if these two networks are connected in series then the impedance matrix of the resulting two-port network will be –
d.) indeterminate
Joule/coulomb is the unit of – a.) Electric field potential b.) Potential c .) Charge
d.) None of the above
The electric field line and equipotential lines-

a.) Are parallel to each other

b.)Are one and same

c.) Cut each other orthogonally

d.)Can be inclined to each other at any angle

For a lossy transmission line short circuited at the receiving end, the input impedance is given by (When Z0 is the characteristic impendence g is the propagation constant and L is the length of the line
When two equal positive point charges are placed along X- axis at X1 and –X1 respectively then the electric field vector at a point P on the positive Y-axis will be directed-

a.) In the +x direction

b.) In the –x direction

c. ) In the +y direction

d.) In the –y direction

The directions of and in TEM mode transmission line with respect to the direction of propagation are-

a.) Both and are transverse to the direction of propagation

b.) is and are transverse and h has a component in the direction of propagation

c.) is entirely transverse and has a component in the direction of propagation

d. ) is entirely transverse and has a component in the direction of propagation

The lowest TM mode in a rectangular waveguide of cross –section a x b with a>b will be-

a.) TM01

b.)TE10

c.) TM112

d.)TE11

When a transmitter in a free space radiates a mean power of ‘p’ watts uniformly in all directions then at a distance d sufficiently far from the source in plane the electric field E should be related to p and d as –
. When a dipole antenna was radiating with some excitation in free space radiating a certain amount of the power v if then this antenna is immersed in a lake where water is non-dissipative but has a dielectric constant of 81, then the radiated power with the same excitation will be

a.) Decrease to finite non-zero value

b.)Remain the same

c. )Increase

d.)Decrease to zero

When a (75 – j40)W load is connected to a coaxial line of Z0 = 75 W at 6MHz then the load matching on the line can be accomplished by connecting-

a.) A short – circuited stub at the load

b.)An inductance at the load

c. )A short circuited stub at a specific distance from the load

d.)none of the above

As compared to analog multimeters, digital multimeters are –a.) less accurateb.) more accurate c.) equally accurate
d.) none.
When a signal of 10 mV at 75 MHz is to be measured then which of the following instruments can be used –a.) VTVMb.) Cathode ray oscilloscope c.) Moving iron voltmeter
d.) Digital multimeter
Which of the following statement is true about two wattmeter method for power measurement in three phase current ?a.) power can be measured using two wattmeter method only for star connected three phase circuits.b.) when two meter show indentical readings, in the power factor is 0.5. c.) when power factor is unit, one of the wattmeter reads zero
d.) when the reading of the two wattmeters are equal but of opposite sign, then the power factor is zero –
When a capacitance transducer has two plates of area 5cm2 each, separated by an air gap of 2mm than the displacement sensitivity in pf/cm due to gap change would be –a.) 11.1b.) 44.2 c.) 52.3
d.) 66.3
The Q of a radio coil –a.) is independent of frequencyb.) increases monotonically as frequency increases c.) decreases monotonically as frequency increases
d.) increases upto a certain frequency and then decreases beyond that frequency
When a generator of internal impedance and operating at 1GHz feeds a load via a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed line is –a.) 0.5b.) 1.5 c.) 2.5
d.) 1.75
The coding system typically used in digital telemetry is –a.) PPM (pulse position modulation)b.) PAM (pulse amplitude modulation) c.) PCM (pulse code modulation)
d.) PDM (pulse duration modulation)
Radiation pyrometers are used for the measurement of temperature in the range of –

a.) -2000C to 5000C

b.) 00C to 5000C

c.) 5000C to 12000C

d.) 12000C to 25000C

In the given figure band structure is shown. It is of –

a.) Gallium Avesenide (GaAs)

b.) Silicon (Si)

c.) Copper (Cu)

d.) Germanium (Ge)

When anode is positive with respect to cathode in an SCR, the numbers of blocked p-n junction is –

a.) 1

b.) 2

c.) 3

d.) 4

The circuit symbol for a GTO is

a. b.

c. d.

In the given fig. mark out the type of Cyclo converters

a.) 1 phase to 1 phase with continuous conduction
b.) 1 phase to 1 phase with discontinuous conduction
c.) step up device
d.) 3 phase to 1 phase device

In the given fig. A-1, C=5, m H and C=20 m F, C is initially charged to 200 V. After the switch.
S is closed at t = 0 the
maximum value of current and the
time at which it reaches this value are respectively.

a.) 400 A, 15.707 mS

b.) 50 A, 30 mSc.) 100 A, 62.828 mSd.) 400 A, 31.414 mS

1. The ratio of two specific heats of air is equal to. = 1.41

2. A perfect gas at 270C is heated at constant pressure till its volume is double. The final temperature is = 3270C

3. An engine operates between temperature of 9000K and T2 and another engine between T2 and 8000K. For both to do equal work, value of T2 will be. = 6500K

4. Internal energy of a substance depends on = Temperature

5. Work done in compressing 1kg of gas adiabatically from p1,V1,T1 to p2, V2, T2 is equal to = Cv(T2-T1)

6. The unit of entropy is = J/kg 0K

7. Indicated power of a 4-stroke engine is equal to = pLAN/2

8. Which of the following is not an internal combustion engine : a) 2 stroke petrol engine b)4 stroke petrol engine c) Diesel engine d) steam engine e) Gas turbine. = (d)

9. If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a) exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high d) engine starts overheating e) all of the above. = (e)

10. The spark plug gap is normally maintained at: = 0.45 to 0.6mm

11. A distributor in spark ignition engines performs the function of : = Providing the correct firing order in engine

12. Which of the following does not relate to C.I. engine:: a) fuel pump b) fuel injector c) governor d) carburetor e) flywheel = (d)

13. Air fuel ratio in a jet engine is = 60:1

14. What is the value of Prandtl No.?

15. In domestic refrigerator, the tubes at the back of the refrigerator are: a) evaporator b) condenser c) capillary tubes d)………

16. Which refrigerants has the highest critical point temperature. = Freon-11

17. Wet bulb temperature is. = indication of amount of moisture in air

18. On psychrometric chart, dry bulb temperature lines are. = Vertical

19. Surface tension has the units. = newtons/m

20. The line of action of the buoyant force acts through the. =centroid of the displaced volume of fluid

21. A pressure of 25m of head of water is equal to. =245kN/m2

22. For a submerged body to be in stable equilibrium, the centre of gravity should be. =Below the centre of buoyancy.

23. The actual velocity at vena contracta for flow through an orifice from a reservoir of height H=?. =Cvv2gH

24. A body weighing 2kg in air weights 2.5kg when submerged in water. Its specific gravity is. = 6

25. In a free vortex motion: = each particle moves in a circular path with a speed varying inversely as the distance from the centre.

26. A centrifugal pump has speed-1000rpm, Flow-1200l.p.m, Head-20m, Power-5H.P. If its speed is increased to 1500rpm, new flow will be.: = 1800l.p.m

27. Runaway speed of a hydraulic turbine is: = the speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open.

28. 10m of water column is equal to = 100kN/m2

29. M.I. of a circular area about an axis perpendicular to the area is: = pr4/2

30. A projectile is fired at an angle ? to the vertical. Its horizontal range will be maximum when ? is . =450

31. An elevator weighing 1000kg attains an upward velocity of 4m/sec in two seconds with uniform acceleration. The tension in the supporting cables will be = 1200kg.

32. A 13m ladder is placed against a smooth vertical wall with its lower end 5m from the wall. What should be the co-efficient of friction between ladder and floor so that it remains in equilibrium. = 0.21

33. A car is moving with a velocity of 60km/hr and possesses energy of 5×105 joules. The mass of the car will be. =3000kg.

34. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR

35. A beam of length l, having uniform load w kg/unit length is supported freely at the ends. The moments at mid span will be: = wl2/8. chetanas.org

36. A boiler shell 200cm dia and plate thickness 1.5cm is subjected to internal pressure of 1.5MN/m2, then the hoop stress will be. = 100N/m2

37. 100KW is to be transmitted by each of two separate shafts. A is turning at 250rpm and B at 300rpm. Which shaft must have greater diameter.: = B

38. Two identical leaf springs of spring constant k are arranged like cantilevers in parallel and attached at free end by a spring of spring constant k. The equivalent spring constant of combination is; = 1.5k.

39. Automobile steering gear is an example of: = lower pair.

40. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.

41. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.

42. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.

43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.

44. Brittle coating technique is used for: = experimental stress analysis.

45. Factor of safety is the ratio of: = yield stress/working stress.

46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.

47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel

48. The product of Cupola is called: = cast iron

49. Brinell tester uses a hardness steel ball of size: = 10mm

50. Sintered and tungsten carbides can be machined by: = EDM

51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.

52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.

53. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.

54. PERT is: = event oriented technique

55. Bar charts are suitable for: = minor works.

56. ? on a PERT/CPM chart represents: = a significant event representing some mile-stone

57. Electron volt is the unit of : = Energy.

58. Seamless tubes are made by?

59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.

60. Why DC current is not used in transformer?

61. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.

62. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?

63. Two cars travel in the same direction at 40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 10:16 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4