#1
13th August 2014, 02:02 PM
| |||
| |||
Papers for UPCL Written Test
Please provide me question paper for recruitment examination organized by Uttarakhand Power Corporation Limited ?
|
#2
14th August 2014, 02:41 PM
| |||
| |||
Re: Papers for UPCL Written Test
Here I am giving you question paper for recruitment examination organized by Uttarakhand Power Corporation Limited below : what is the advantages and dis advantages of critical speed of turbine What will happen if oil is mixed with boiler feed water? What are the differences between heat transfer and mass transfer? in what cycle steam power plant is based how can calculate how much steam is to be required for generation of 1MW electricty? what is ERW PIPE & Seamless PIPE Out of ERW and Seamless which one gives good results for an impact force of 2700 N?? What are the protections required to protect turbine? what is the difference between suction lift & suction head? what is the defination of an ideal fluid? What is the knee point of voltage of CT? how fault in an electric system is detected & hw protection of equipments is done ? How the cable size for a motor is decided In a Synchronous generator, Can AC voltage be used instead of DC voltage in field winding of rotor to produce AC power? what happen ,if generator will generate leading power factor? In microprocessors, what does the mnemonic SKIP do? The peripherals of the computer(like keyboard, monitor) are connected through buses directly or is there any interfacing device present in the CPU? what is the difference between squirrel cage & slip ring induction motor? Why a transformer Noise during its running condition ? how do you come to know air is fully saturated WHY TRANSFORMERS ARE RATED IN 11KV 22KV 33KV Instead off 10kv 20kv 30kv 1)Why electric shock is feel ?? n in a Electric Train why we didnt feel that ? 2)What is the reason for transformer Noise ?? 3)What is relation b/w Transmission Lines & Communication Lines ? 4)Which material is used for making Transformer oil & How u measure its dielectric strength & Name the test ? an ice block submurged in the water, if the ice melt level of water 1. Given four unit-circle plots identify the one corresponding to a bandpass filter. 2. A 4 kHz signal is sampled at thrice the Nyquist rate and sent through a channel with error ?1%. Calc the bandwidth of the channel. 3. Given a two port network in the form of a T find o/p admittance in terms of yparameters. 4. Connect two 1? resistors in series, then connect two 1H inductors across one of the resistors such that the ckt looks like a 1? resistor in series with a ?-section of a resistor and two inductors. With the series resistance on the i/p side, calc the transfer function of this ckt 5. Inverse laplace transform of 1/s2[d/ds(e-3s/s)] 6. Lower useful input limit of a transducer is determined by… 7. Air-cored inductors are used for low frequency/high frequency/equal frequency operations. 8. Given 4 pole-zero plots identify which one corresponds to the driving point impedance of a series resonant ckt. UPCL question paper in a more detail for atteched pdf file... |
#3
26th September 2014, 04:09 PM
| |||
| |||
Re: Papers for UPCL Written Test
provide me upcl electrical question paper. Regards |
#4
17th March 2015, 07:51 AM
| |||
| |||
Re: Papers for UPCL Written Test
I am doing the preparation for the UPPCL Electronics exam? So I am searching for the Question Paper for the UPCL Electronics Written Test? Can you please provide me the UPPCL Electronics Question Paper?
|
#5
17th March 2015, 08:26 AM
| |||
| |||
Re: Papers for UPCL Written Test
You are asking to UPPCL Electronics Written Test Question Paper. Here I am uploading a file that contains the UPPCL Electronics Written Test Question Paper. You can download this from here. Here I am also providing you some content t of the file. This is as follows: 1. For one of the following conditions, clocked J-K flip-flop can be used as DIVIDE BY 2 circuit where the pulse train to be divided is applied at clock input. a) J = 1, k = 1 and the flip- flop should have active HIGH inputs b) J = 1, k = 1 and the flip- flop should have active LOW inputs c) J = 0, k = 0 and the flip- flop should have active HIGH inputs d) J = 1, k = 1 and the flip- flop should be a negative edge triggered one 2. Number of comparators needed to build a 6-bit simultaneous A/D converter is a) 63 b) 64 c) 7 d) 6 3. The AID converter used in a digital voltmeter could be (1) successive approximation type (2) Flash converter type (3) Dual slope converter type. The correct sequence in the increasing order of their conversion time taken is a) 1, 2, 3 b) 2, 1, 3 c) 3, 2, 1 d) 3, 1, 2 4. Which of the following binary number is equal to octal number 66.3 a) 101101.100 b) 1101111.111 C) 111111.1111 d) 110110.011 A 4-bit presetable UP counter has preset input 0101. The preset operation takes place as soon as the counter reaches 1111. The modulus of the counter is a) 5 b) 10 c) 11 d) 15 5. A 4-bit synchronous counter uses flip-flops with propagation delay time of 25 ns each. The maximum possible time required for change of state will be a) 25 ns b) 50 ns c) 75 ns d) 100 ns 6. If a counter having 10 FFs is initially at 0, what count will if hold after 2060 Pulses a) 000 000 1100 b) 000 001 1100 c) 000 001 1000 d) 000 000 1110 7. Memory chips, which have 12 address lines and 4 data lines each. The number of such chips required to design the memory system is a) 2 b) 4 c) 8 d) 16 8. In time division multiplexing a) Time is doubled between bits of a byte b) Time slicing at CPU level takes place C) Total time available in the channel is divided between several users and each users is allotted a time slice. d) None of the above UPPCL Electronics Written Test Question Paper |