#1
8th August 2014, 09:00 AM
| |||
| |||
I am looking for Industrial Training Institute Fitter exam question paper, will you please provide here??? You are looking for the Industrial Training Institute Fitter exam question paper, i am giving here: 1.A finish cut is given to improve the surface finish of a rough milled workpiece? A.Decrease cutting speed, feed rate and depth of cut B.Increase feed rate, depth of cut and reduce cutting speed C.Increase feed rate, depth of cut and cutting speed D.Increase cutting speed, reduce feed rate and depth of cut Ans: D 2.The normal module of a helical gear with real module (m) of 6.62 and having an angle of 25 deg is? A.6.62 x sin 25 deg B.6.62 x cos 25 deg A.6.62 x tan 25 deg A.6.62 x cot 25 deg Ans: B 3.Thread ring gauges are used check external threads. Separate 'Go' and 'No Go' gauging members are provided. Which one of the following screw thread elements is not checked with the ring gauges? A.Pitch B.Helix angle C.Profile D.Pitch diameter Ans: B 4.Morse taper is one of the internationally accepted standard tapers. The morse taper are available in numbers from? A.0 to 7 B.0 to 8 C.1 to 7 D.1 to 8 Ans: A 5.A gear wheel has 36 teeth (z) and 3 mm module (m) its pitch diameter cutter? A.12 mm B.75 mm C.80 mm D.108 mm Ans: D 6.A main purpose of using worm and worm wheel drives in machines and their accessories is to? A.Transmit large torque B.Provide large speed reduction from worm shaft to worm wheel C.Transmit higher speeds D.Provide large speed reduction from worm wheel to worm shaft Ans: B 7.The tooth thickness of rack is measured by? A.Universal vernier caliper B.Gear tooth vernier caliper C.Flange micrometer D.Gear tester Ans: B 8.There are two types of milling processes based on the direction of cutter rotation and work feed direction in up cut milling? A.The work is fed in the same direction as the rotation of the cutter B.Chip removal starts at the thickness part C.Machine with backlash eliminator is essential D.The work is fed against direction of the cutter rotation Ans: D 9.A Shaft is turned in one finish cut which one of the following parameters will directly influence the machining time? A.Cutting depth B.Setting angle C.Diameter of work piece D.Tool travel distance Ans: D 10.In a planning machine the depth of cut is given by? A.Adjusting tool slide B.Rotating the feed screw of the tool holder C.Moving cross slide D.Lifting the work piece Ans: B 11.You have to machine a flat surface on a work piece of two metres length. Which machine will you choose for this? A.Planning B.Slotting C.Milling D.Shaping Ans: A 12.Why it is necessary to maintain an approach distance between the cutting tool and the work while working on shaping machine? A.To cool down the cutting edge of the tool bit B.To avoid any ridger at the end of workpiece C.To allow the chips to fall and clear the cutting edge D.To enable the clapper box to return to cutting Ans: D 13.Oil grooves are to be cut in brass half bearings. Which one of the following chisels in suitable? A.Flat chisel B.Cross chisel C.Half round nose chisel D.Web chisel Ans: C 14.The quality control allows at the most 0.4% defective parts, How many defective parts can be allowed in a production of 500 parts? A.1 B.2 C.10 D.20 Ans: B 15.One which unit the tool setting is done on NC machine? A.On special devices away from the machine B.On the NC machine during idle time C.On the pre setting devices D.None of above Ans: C 16.The component of the surface texture upon which the roughness is superimposed is known as? A.Surface roughness B.Surface texture C.Lay D.Waviness Ans: D 17.Which one of the following groups of properties enables the manufacture of chain hooks from wrought iron? A.Ductillity, malleability and hardness B.Hardness, toughness and ductility C.Malleability, ductility and toughness D.Hardness, toughness and brittleness Ans: C 18.You have to file an aluminum block to a smooth finish, which one of the following cut of file is most suitable? A.Double cut B.Curved cut C.Rasp cut D.Single cut Ans: A 19.Which one of the following is an artificial abrasive? A.Emery B.diamond C.Corundum D.Silicon carbide Ans: D 20.The grain size of a grinding wheel is indicated by numbers, which range of grain size referred to as 'Very Fine'? A.10 - 24 B.30 - 60 C.80 - 180 D.220 - 600 Ans: D 21.A high carbon steel has to be forged, which colour indicate the most suitable forging temperature? A.Yellow red B.Dark cherry red C.white D.Light yellow Ans: A 22.The lead screw pitch of a milling machine is 5mm and the dividing head ratio is 40 : 1 the lead of the milling machine is? A.0.125 mm B.5 mm C.8 mm D.200 mm Ans: D 23.The axis of the plate cam blank and the end mill spindle should always remain? A.Inclined to each other B.Parallel to each other C.Opposite to each other D.Vertical and inclined Ans: B 24.Which milling machine is particularly adopted for milling internal or external profiles? A.Pantograph milling machine B.Universal milling machine C.Planetary milling machine D.Tracer controlled milling machine Ans: D 25.A 42 teeth involute helical gear with a helix angle of 45 deg is to be cut on a milling machine? A.12 to 13 B.35 to 54 C.135 to rake D.17 to 20 Ans: B 26.CNC machine are not manually operated. They are controlled by means of? A.A programme B.An operating C.A cam D.A plug board system Ans: A 27.Counter boring is done for? A.Deburring hole ends B.Enlarging holes to accurate size C.Finishing cored holes D.Accommodating socket head screws Ans: D 28.A point to point control system is suitable only for one of the following applications? A.Milling profile B.Turning C.Drilling D.Grinding Ans: C 29.A steel workpiece of height tensile strength is to be machined with a HSS milling cutter, which one of the following rake angles is best suited for the cutter? A.8" B.12" C.20" D.28" Ans: A 30.By using quick return mechanism in shaping machine the cutting stroke moves slow and return stroke fast. what is the ratio between cutting stroke and return stroke? A.2:3 B.3:2 C.5:3 D.3:5 Ans: B 31.What will be the result if the clearance angle in drill is increased? A.Poor wedging action B.Weak cutting edge C.Rough hole surface D.Increased point angle Ans: B 32.An irregularly shaped workpiece is turned on a lathe. which one of the following work holding accessories is used? A.Three jaw chuck B.Two jaw chuck C.Driving plate D.Face plate Ans: D 33.Solid H.S.S. cutters and carbide inserted tooth cutters are commonly used for milling, the permissible cutting speed of an inserted tooth cutter in relation to that of a HSS cutter is? A.Twice as much B.Five to ten times greater C.smaller D.Same Ans: A 34.It is required to machine a single start worm of 2 module (m) and 60 mm pitch diameter, the speed ration is 40:1, to what length should the worm be cut? A.21 mm B.14.6 mm C.29.3 mm D.33.3 mm Ans: C 35.The pattern on the work surface caused by the movement of the cutting tool is called? A.Waviness B.Roughness C.Surface texture D.Lay Ans: C 36.A product is said to have the quality when? A.Its shape and dimensions are within the limits B.It appears to be very good C.It is fit for use D.The choice of material is right Ans: C 37.Which taper is used on spindle nose of the lathe head stock? A.Jerno taper B.Brown and sharp taper C.Pin taper D.Morse taper Ans: D 38.Why do you hold a workpiece lengthwise while machining in a planning machine? A.It is easier to load workpiece lengthwise B.The idle time will be minimised C.The surface quality will be improved D.The tool life will be increased Ans: C 39.A hole whose lower deviation is zero is called basic hole, which one of the following letters indicates basic hole? A. E B. F C. G D. H Ans: D 40.Rough and finish boring operations are carried out to machine a hole in a milling machine, for rough boring select? A.High spindle speed and coarse feed B.slow spindle speed and coarse feed C.slow spindle speed and fine feed D.High spindle speed and fine feed Ans: B Books Fitter Shop 1000 Questions-Answers , 2nd Edition by Kapil Dev Last edited by Shaleen; 4th July 2019 at 08:55 AM. |
#2
5th August 2015, 03:59 PM
| |||
| |||
Jing jiska adhar na ho lekin drill hokr job par set kiya ja sake use kya kahate h
|
#3
1st February 2016, 06:10 PM
| |||
| |||
[QUOTE=Quick Sam;99616]Yo lakhandehariya@rediffmail.com |
#4
27th November 2019, 08:34 AM
| |||
| |||
Re: Model paper for ITI Fitter
Can you provide me the ITI (Industrial Training Institutes) Fitter Model Question Paper in Hindi as I need it for preparation of the examination?
|
#5
27th November 2019, 08:35 AM
| |||
| |||
Re: Model paper for ITI Fitter
The ITI (Industrial Training Institutes) Fitter Model Question Paper in Hindi as I need it for preparation of the examination is as follows: 1. निम्न में से गियर्स का प्रयोग पॉवर को, दो समानांतर शाफ्टों के बीच ट्रांसमिट करने में किया जाता है : • वर्म गियर्स • हैलकल गियर्स • स्पर गियर्स • मिटे गियर्स उत्तर- स्पर गियर्स 2. ड्रिलिंग मशीन की कंपाउंड टेबल उपयोग की जाती है। • जब एक ही कम्पोनेंट में अधिक संख्या में होल ड्रिल करने हेतु • साधारण कार्य हेतु। • काउंटर सिकिंग हेतु • काऊंटर बोरिंग विशेष हेतु। उत्तर- जब एक ही कम्पोनेंट में अधिक संख्या में होल ड्रिल करने हेतु 3. स्कू पिच गेज के ब्लेड निम्न में से धातु के बनाकर कठोरीकृत किए जाते हैं • हार्ड कार्बन स्टील • कास्ट आयरन • माइल्ड स्टील • स्प्रिंग इस्पात की चद्दर उत्तर- स्प्रिंग इस्पात की चद्दर 4. पीने के पानी को घरों तक पहुँचाने के लिए निम्न में से पाईप प्रयोग किया जाता है: • जी. आई. पाईप • एल्युमीनियम पाईप • कॉपर पाईप • प्लास्टिक पाईप उत्तर- जी. आई. पाईप 5. एसीटीलीन गैस को घुली हुई अवस्था में रखने के लिए निम्न में से दाब की आवश्यकता होती है: • 14-16kg/Cm • 15-16kg/Cm • 12-14kg/Cm • 13-16kg/Cm उत्तर- 15-16kg/Cm 6. टांग वाइस निम्न में से धातु की बनायी जाती है : • ढलवा लोहा • हाई कार्बन इस्पात • सादा कार्बन इस्पात • मृदु इस्पात उत्तर- मृदु इस्पात 7. फीड की दर निम्न में से निर्भर करती है : • वांछित परिष्करण • ड्रिल की किस्म पदार्थ • छिद्र किए जाने वाला पदार्थ • उपरोक्त सभी उत्तर- उपरोक्त सभी 8. किस यंत्र द्वारा जॉब की सतह की हिल्स एण्ड वैलीज की जाँच की जा सकती हैं – • प्रोफाइल मीटर द्वारा • बैरोमीटर द्वारा • एमीटर द्वारा • उपरोक्त सभी उत्तर- एमीटर द्वारा 9. पंच एवं ड्रिफ्ट निम्न में से प्रतिशत कार्बन इस्पात से बनाए जाते • 0.9% • 0.7% • 0.6% • 0.8% उत्तर- 0.9% 10. रोलिंग एलीमेंट, रेस तथा केज निम्न में से किस बीयरिंग के लक्षण • एंटी बीयरिंग • सॉलिड बीयरिंग • स्लिप्ट बीयरिंग • प्लेन बीयरिंग उत्तर- एंटी बीयरिंग 11. अन्तर्परिवर्तनीय ा (Interchangeability) से मशीनों का……………..टाइम कम होता है। • आइडल • रनिंग • रिसॉल्विंग • इनमें से कोई नहीं उत्तर- आइडल 12. बाहरी माइक्रोमीटर का स्पींडल निम्न पर लगा होता है: • फ्रेम पर • बैरल पर • थिम्बल पर • एनवील पर उत्तर- थिम्बल पर 13. मूल साइज पर निम्न में से विचलन दिए जाते हैं • विमाओं • साइज • रेखाओं • मानक उत्तर- विमाओं 14. व्हाइट मेटल बीयरिंग में निम्न में से कौन से एलाय पाए जाते हैं : • कॉपर • टिन • एंटीमनी • A व C उत्तर- A व C 15. जब एल्युमीनियम, ताँबा , सीसा जैसे मुलायम पदार्थों का अपघर्षण किया जाता है तो धातु के कण पहिए के निम्न में से फस जाते हैं: • रन्धों • आँख- शील्ड • सुरक्षा कवच • टूल रैस्ट उत्तर- रन्धों 16. छिद्र के निचले विचलन को क्या कहते हैं? • EI • ES • ER • Ei उत्तर- EI 17. निम्नलिखित में से छैनियों की अनुप्रस्थ काट होती है : • त्रिभुजाकार • पंचभुजाकार • षट्भुजाकार • सप्तभुजाकार उत्तर- षट्भुजाकार 18. जब कार्यखण्ड की लम्बाई (Length) उनके व्यास की 10 गुना (Times) या अधिक हो तब ”””””। • रेस्ट (Rest) का प्रयोग अवश्य करना चाहिए। • सेण्टर्स (Centers) का प्रयोग अवश्य करना चाहिए • लेथ मशीन पर लम्बी शाफ्टों की टर्निग (Turning) की जानी • चाहिए। • कटिंग स्पीड (Cutting Speed) बढ़ा देनी चाहिए। उत्तर- रेस्ट (Rest) का प्रयोग अवश्य करना चाहिए। 19. बेबिट मैटल IZK;: निम्न में से प्रमुख मिश्रण है : • टिन • जस्ता • पीतल • जिंक उत्तर- टिन 20. मूबेबल जॉ पर कैलीपर डायल कितने डिविजन में ग्रेजुएट रहते है : • 50 डिविजन • 100 डिविजन • 150 डिविजन • 10 डिविजन उत्तर- 100 डिविजन 21. ब्रिटिश माइक्रोमीटर का अल्पतमापांक निम्न में से है : • 0.001 मि. मी. • 0.002 मि. मी. • 0.005 मि. मी. • 0.006 मि. मी. उत्तर- 0.001 मि. मी. 22. निम्नलिखित में से गियर्स की अक्षीय भ्रस्ट न्यूनतम होती हे : • हैलीकल गियर्स • स्पर गियर्स • ट्रेटिंग कोण • मिट्रे गियर्स उत्तर- स्पर गियर्स 23. चूड़ी-कर्तन प्रक्रम (Thread Cutting Process) के लिए किस मशीन का प्रयोग करते हैं? • लेथ मशीन • ड्रिलिंग मशीन • स्क्रैप मशीन • फोल्डिंग मशीन उत्तर- लेथ मशीन 24. धातु चादरों को जोड़ने के लिए निम्न में से विधि है • नट-बोल्ट • सोल्डरिंग • वैल्डिंग • क्लैम्पिंग उत्तर- सोल्डरिंग 25. वर्नियर गहराई गेज का प्रयोग निम्न के लिए किया जाता है : Bottom • छिद्र खांचे मापने • वस्तु की गहराई मापने • पदों को मापने • उपरोक्त सभी उत्तर- उपरोक्त सभी 26. आन्तरिक रक्तस्राव होने का निम्न में से कौन-सा कारण नहीं है? • किसी आन्तरिक हड्डी का टूट जाना • फेफड़ों और गुर्दो से रक्तस्राव होना । • किसी अंग का कट जाना। • विकृत यकृत या तिल्ली से रक्तस्राव होना उत्तर- किसी अंग का कट जाना। 27. हूक रूल से निम्न में से चौड़े छेद तक माप सकते हैं : • 15 मि.मी. • 25 मिमी. • 50 मि.मी. • 10 मिमी. उत्तर- 15 मि.मी. 28. स्प्रिंग निम्न में से धातु के बने होते हैं : • उच्च कार्बन इस्पात या स्प्रिंग स्टील • ताँबा • स्टेनलेस स्टील • ड्रॉप फोर्जड इस्पात उत्तर- उच्च कार्बन इस्पात या स्प्रिंग स्टील 29. दस्ती रिवेटिंग में रिवेटन का निम्न में से दोष है: • सीधे ड्रिल नहीं होते • प्लेटों का सही जुड़ना • ड्रिल छिद्रों में रेशों नहीं होते • सीधे ड्रिल होते हैं। उत्तर- सीधे ड्रिल नहीं होते 30. भट्टी में निम्न में से प्रतिशत कार्बन तक के इस्पात फोर्जन करने योग्य होगें है : • 1.5% • 1.6% • 1.8% • 1.7% उत्तर- 1.7% 31. एक ड्रॉइंग पर 3550002 मिमी दर्शाया गया है, इसकी टॉलरेन्स है। • 0.002 मिमी • 35.002 मिमी • 35 मिमी • 0.004 मिमी उत्तर- 0.004 मिमी 32. मशीनों के पुनसंयोजन से आशय है • अवयवों को साफ-सफाई एवं तेलयुक्त करके मशीन में पुनः फिट करना • मशीन अवयवों को खराब होने पर बदलना • मशीन अवयवों को मशीन से अलग करना • उपरोक्त में से कोई नहीं उत्तर- अवयवों को साफ-सफाई एवं तेलयुक्त करके मशीन में पुनः फिट करना 33. निम्न में से हैम के प्रकार है • इकहरा हेम • दोहरा हेम • तारदार हेम • उपरोक्त सभी उत्तर- उपरोक्त सभी 34. टेम्प्रेचर एरर में रिफरेंस का तापमान निम्न में से सेट किया जाताहै: • 400 सेंटीग्रेड • 150 सेंटीग्रेड • 350 सेंटीग्रेड • 200 सेंटीग्रेड उत्तर- 200 सेंटीग्रेड 35. निम्न में से बेल्ट ड्राइव का प्रयोग तब किया जाता है जब शाफ्ट के बीच की दूरी चपटी बेल्ट के लिए काफी कम हो • फ्लैट • रिब्ड • दांतेदार • वी – बेल्ट उत्तर- दांतेदार 36. आकार एवं साइज में अधिक परिशुद्धता की आवश्यकता न होने पर पदार्थ हटाने की संक्रिया को निम्न में से कहते हैं: • हैण्ड अपघर्षण • ऑफ ग्राइंडिंग • पेडस्टल ग्राइंडर • ऑफ हैंड अपघर्षण उत्तर- ऑफ हैंड अपघर्षण 37. यूनिफाइड चूड़ियों का कोण निम्न में से होता हैं: • 60° • 90° • 120° • 30° उत्तर- 60° 38. हथौड़ी का चीक निम्न में से छोड़ दिया जाता है : • कठोरीकृत • मृदु • टेम्पर • फोर्जड उत्तर- मृदु 39. साधारण कैलीपर्स का साइज होता है । • टाँगों की लम्बाई • मापी जाने वाली अधिकतम लम्बाई • रिवेट के सेण्टर से नोंक तक की लम्बाई • उपरोक्त में से कोई नहीं । उत्तर- रिवेट के सेण्टर से नोंक तक की लम्बाई 40. विचलन सहित साइज की विमांकन सीमा निम्न में से कहलाती है : • विमांकन • विचलन • फिट • व्यतिकरण उत्तर- विमांकन 41. ड्रिल में शंकु के आकार का सिरा जो काटने का काम करता है, वह कहलाता है : • बिंदु /नोंक • शेंक • टैप • इनमें से कोई नहीं उत्तर- बिंदु /नोंक 42. ब्रिटिश प्रणाली में लम्बाई के मान की इकाई निम्न में से • 1/64 इंच • 0.05 मि. मी. • 0.01 इंच • 1/38 इंच उत्तर- 1/64 इंच 43. चाँदी ब्रेजिंग की विधि निम्न में से तापक्रम के बीच होती है : • 600° – • 5000-650°C • 3000-350°C • 4500 – 600°C उत्तर- 850°C 44. सबसे हल्की प्लास्टिक निम्न में से है • नायलोन • पॉली प्रोपलीन • पॉलीथीन • PVC उत्तर- पॉली प्रोपलीन 45. बड़े व्यास के पाइप में आगे कम व्यास का पाइप जोड़ने के लिए निम्न में से क्या प्रयोग किया जाता है? • प्लग • यूनियन • रिड्यूसिंग सॉकेट • स्टॉप कॉक उत्तर- रिड्यूसिंग सॉकेट 46. निम्नलिखित में से ड्रिलिंग का दोष नहीं है : • बहुत बड़ा छिद्र • अति तप्त ड्रिल • खुरदरा छिद्र • फीड पर बहुत अधिक होना। उत्तर- फीड पर बहुत अधिक होना। 47. स्टील स्क्वायर निम्न में से वर्ग का साइज प्रदर्शित करेंगें: • लम्बाई और चौड़ाई से • ऊँचाई और गहराई से • बॉडी, लंबाई एवं कोण द्वारा • बॉडी एवं लम्बाई द्वारा उत्तर- बॉडी, लंबाई एवं कोण द्वारा 48. वर्नियर स्केल पर 1′ के 10 तथा 1 भाग के कितने अनुभाग (Sub-Division) होते हैं? • 2 • 4 • 5 • इनमें से कोई नहीं उत्तर- 4 49. शाफ्ट के ऊपरी विचलन एवं निचले विचलन को क्रमश: निम्न में से द्वारा व्यक्त करते हैं : • Es, EI • Es, Ei • Es, Ie • इनमें से कोई नहीं उत्तर- इनमें से कोई नहीं 50. माइक्रोमीटर के एनविल किस धातु के बने होते हैं? • टंग्स्टन कार्बाइड • हाई स्पीड स्टील • हाई-कार्बन स्टील • इनमें से कोई नहीं उत्तर- टंग्स्टन कार्बाइड |