MAHAGENCO sub engineer syllabus and sample question papers

I am searching for the MAHAGENCO sub engineer syllabus and sample question papers? Please tell me from where I can download the MAHAGENCO sub engineer syllabus and sample question papers?

[Kiran Chandar]

You are asking for the MAHAGENCO Sub Engineer post syllabus. The published the recruitment of the MAHAGENCO Sub Engineer. The applicant who want to apply for this post must have Diploma Holder of university or institute in India or incorporated by or under central act or state act or any other qualification recognized as equivalent to AMIE with any one of the above branches

Pay Scale: Rs 11600-520-14200-540-19600-565-32030/-

Age Limit: 33 years (as on 31st August, 2012)

Upper age limit is relaxable by 5 years for the candidates belonging to backward classes; Ex-Servicemen/PwD/Project Affected Person will be 45 years
Upper age limit is not applicable to the departmental employees working in MAHAGENCO Application

Syllabus
Power Electronics
A C machine
Analog Circuits
Control System
DC Machine
Digital Electronics
Electrical Basics
Network theory

Here I am providing you the MAHAGENCO sub engineer sample question papers. These are as follows:


APTITUDE
1. 1. Find the amount obtained by investing Rs. 24, 000 at 18% per annum simple interest for five
years?
1] Rs. 21, 600 2] Rs. 44, 000 3] Rs. 48, 000 4] Rs. 45,
600

2. A number when increased by 30% becomes 78. What is the number?
1] 60 2] 70 3] 40 4] 48

3. A two-digit number is such that twice the ten’s digit add to eleven times the units digit is equal to
the number itself. What is the number?
1] 48 2] 86 3] 73 4] 54

Direction for question 4 and 5: Fill in the blank in the given sentence so as to make sense. Select the correct word from the answer choices and mark its number as the answer.

4. A welcoming party was _________ the day after the new teach arrived.
1] conducted 2] thrown 3] initiated 4] organised

5. The store _________ medicines as well as cosmetics.
1] stocks

MAHAGENCO Civil Engineer Question Papers

1. Which of the following is/are the assumption(s) of Bernaulli’s equation?
1] There is loss of liquid while flowing.
2] There is no external force except the gravity acts on the liquid.
3] The velocity of energy of liquid particle, across any cross-section of pipe is uniform.
4] Both [2] and [3]

2. In constructions, why are the lintels preferred to arches?
1] Arches will not long last
2] Arches require more head room to span the open as like doors, windows etc.
3] Arches require strong abutments to withstand arch thrust
4] Bothe [2] and [3]

3. What is called a ‘level line’?
1] The line parallel to the mean sphireodal surface of earth
2] The line is horizontal
3] The line passing through the centre of cross-hairs and the centre of the eye piece
4] The line passing through the objective lens and the eye piece of a dumpy or tilting level


MECHANICAL ENGINEERING
1. The chronological order of strokes in a four stroke petrol engine is:
1] Suction stroke, working stroke, compression stroke and exhaust stroke.
2] Suction stroke, compression stroke, working stroke and exhaust stroke.
3] Compression stroke, working stroke, suction stroke and exhaust stroke.
4] Compression stroke, suction stroke, working stroke and exhaust stroke.

2. The enthalpy of steam is defined as:
1] Difference of internal energy and product of pressure and volume.
2] Product of internal energy and pressure.
3] Sum of internal energy and product of pressure and volume.
4] Amount of heat change divided by the absolute temperature.

3. Which of the following operations can be performed using a drilling machine?
A. Reaming B. Countersinking C. Spot Facing D.
Thread tapping
1] Only A, B and D 2] Only B, C and D 3] Only A, B and C 4] All of
these

4. Which of the following are the advantages of impulse turbine over reaction turbines?
A. Occupies less space per unit power.
B. Compounding is not necessary for speed reduction as the rotor speeds are usually low.
C. Suitable for high power generation.
1] B and C only 2] A only 3] C only 4] A and C only

ELECTRICAL
1. The speed of an AC motor depends on ____ .
1] Frequency 2] Number of poles 3] Both [1] & [2] 4] None of these

2. The speed of the motor can be varied by ___.
1] Changing supply frequency 2] Changing number of poles
3] Using multi speed windings 4] All of these

3. Output power requirements of constant torque loads vary with _____.
1] Speed 2] voltage 3] Current 4] power factor

4. Maximum demand controller is used to ___________.
1] Switch off essential loads in a logical sequence
2] Exceed the demand of the plant
3] Switch off non-essential loads in a logical sequence
4] Controls the power factor of the plant

5. Select the application of fluid coupling fitting from the following:
1] Acts as a voltage limiter 2] Enables no-load start-up of prime-mover
3] Works on the principle of eddy current 4] None of these

ELECTRONICS

1. The stability factor is defined as:
1] ΔIc/Δβ 2] ΔIc/ΔIco 3] ΔIc/ΔVBE 4] All of these

2. Among the circuit stabilization techniques ___________gives better stable operating point.
1] Voltage divider biasing circuit or self biasing circuit 2] Base biasing circuit or fixed biasing circuit
3] Collector feedback biasing circuit 4] None of these

3. Normally emitter region in transistor is:
1] Heavily doped
2] Very lightly doped
3] Doped in between that of base region and collector region
4] None of these

4. Both in n-p-n and p-n-p transistors neglecting the reverse saturation current emitter Current is:
1] The sum of collector current and base current
2] The difference of collector current and base current
3] The product of collector current and base current
4] Both emitter and base current direction

5. The knee voltage of silicon diode is equal to?
1] 5 V 2] 0.5V 3] 0.7V 4] 1V

I am appearing in MAHAGENCO sub engineer exam and I am starting my preparation for that I need syllabus or sample question paper of it so can you provide me this?

[Pathak]

Ok, here I am sharing the syllabus of MAHAGENCO sub engineer exam so that you can start your preparation as soon as possible

Syllabus

Electrical:
Power Electronics
A C machine
Analog Circuits
Control System
DC Machine
Digital Electronics
Electrical Basics
Network theory

Electronics:
Control Systems
Digital Electronics and Logic Design
Electronics Devices and Circuits
Micro processor/Microcontrollers
Operational Amplifiers
Power Electronics
Principles of Communication engineering

Electronics & Power:
AC power transmissions
Bulk power transmissions
Distribution of power
Generation of electrical power
Electronics & Communication/Basics

Electronics & Telecomm:
Analog Circuits
Basics
Integrated Circuits and Digital Electronics
Micro Processor and Micro Controllers
Other Electronic Devices
PLT
Semiconductors and Transistor Devices

Mech:
Applied Mechanics
Fluid Mechanics
Hydraulic Machines
Machine Design
Pipe and Fitting
Refrigeration and Air Conditioning
SOM
Theory of machines
Welding Technology
Workshop Technology
Thermodynamics

Civil:
Basic Soil Mechanics
Foundation Engg
Soil Exploration
Fluid Mechanics
Water Supply Engg
Structural Engineering – 1/Construction Materials
Structural Engineering – 1/Construction Planning & Management
Transportation Engineering/Airport & Harbor Engg
Transportation Engineering/Highway Engg

Instrumentation:
Fundamentals
Transducers
Electronics
Control System
Digital Circuits
Micro processors &Microcontrollers
Measurments
Transistors and op amps