#1
3rd August 2015, 09:47 AM
| |||
| |||
KSEB model question paper
Hello sir I am mukesh and going for appear in KSEB Assistant Engineer recruitment exam and for preparation of this exam I want to collect its modal paper will you plz provide me here
|
#2
3rd August 2015, 12:41 PM
| |||
| |||
Re: KSEB model question paper
As you are going to appear in KSEB Assistant Engineer recruitment exam , so here I am telling you about this exam pattern : In KSEB Assistant Engineer recruitment exam : Each question carries 1 mark. There are no negative markings. Answers will be provided for the attempted questions only. Please try to answer all the question. On your demand here I am providing a sample paper of KSEB Assistant Engineer recruitment exam: 1) The CPU of a computer consists of None of the above Memory and ALU INPUT and OUTPUT Unit ALU and Control Unit 2) The capacitance connected between the I/P and O/P of an amplifier affects its high frequency response due to MILMAN effect MILLER effect COLPIT effect COLLINS effect 3) Which instrument is used to measure low values of resistance ? Maxwell Bridge Kelvin Double Bridge Wheatstone Bridge Anderson Bridge 4) An ideal OP-AMP has infinite gain infinite input impedance infinite bandwidth all of the above 5) The number of flip flops required in a decade counter is 3 4 10 2 6) For stability and economic reasons we operate the transmission line with power angle in the range 10° to 25° 65° to 80° 60° to 75° 30° to 45° 7) The transfer function is defined for Linear and time-variant system Linear and time-invariant system Non-linear and time-variant system All of the above 8) A dc cumulatively compounded motor delivers rated torque at rated speed. If the series fields is short circuited then the armature current and speed will decrease and increase respectively both increase increase and decrease respectively both decrease 9) The collector current of transistor is always less than emitter current none of the above greater than emitter current equal to emitter current 10) Which one of the following is not an image file format ? image.png image.pdf image.jpg image.bmp 11) When resonance occurs in a circuit, the pf is 1 less than 1 0 greater than 1 12) Two devices commonly used to generate light for fiber optic communication system LED and LCD LED and TFT All of the above LED and ILD 13) While drawing the phasor diagram of a parallel circuit, which one is taken as the reference None of the above Voltage Power Current 14) A voltmeter gives 120 oscillations per minute when connected to the rotor of an induction motor. When the stator frequency is 50Hz, slip of the motor is 5% 4% 2.5% 2% 15) Steady state stability of a power system is improved by reducing fault clearing time single pole switching using double circuit line decreasing generator inertia 16) Base modulation is used in TV transmission because All of the above Large power O/P and better efficiency High degree of linearity Power required is small 17) The most commonly used detector in AM receiver is Coherent detector Ratio detector Discriminator Envelope detector 18) Which one of the following is a synchronous optical network ? TELNET INTERNET DELNET SONET 19) The Hall effect voltage in intrinsic silicon changes sign on application of magnetic field is positive is zero is negative 20) The value of coefficient of coupling is always greater than 1 none of the above equal to 1 less than 1 21) An analog computer used for resolving a vector into two mutually perpendicular components has a device called Register Resolver Subroutine None of these 22) Which one of the following devices is not used for networking ? Cub Hub Switch Router 23) The residual magnetism of a self-excited dc generator is lost. To build up its emf again the fieldd winding must be replace the field winding connection must be reversed its armature connection must be reversed field winding should be excited by low voltage DC voltage 24) In an EXCLUSIVE-OR gate, when the O/P is zero, the inputs are 1,0 0,1 1,x 1,1 25) Silicon devices are used for high temperature application compared to germanium because silicon is more thermally stable none of the above silicon can dissipate more power reverse saturation current is less in silicon 26) Ferranti effect is experienced on long transmission lines when it is lightly loaded on full load at upf on full load at 0.8 pf lag all of the above 27) Which region of the transistor characteristic is used for amplification active cut off saturation passive 28) The ASCII code is 7 bit code 9 bit code 5 bit code 11 bit code 29) An automatic iron box is an example of none of the these an open loop control system a multi feedback control system a single feedback control system 30) A series circuit containing passive elements has the following voltage and current v = 100 sin (314t + 50 ) and i = 4 cos (314t + 13 ). The circuit elements must be L, C and R could be either R and C or R, L and C must be R and L must be R and C 31) A cache in a computer is used to hold more date used to improve the storage capacity used to increase the speed of execution none of the above 32) Which one of the following is not related to modems? DCE data phone Telephone data-set 33) When two capacitors C1 and C2 are connected in series, the equivalent value of capacitance is C1C2/(C1 + C2) C1C2 C1 + C2 C1 – C2 34) When the supply frequency is decreased the capacitive reactance increases decreases unpredictable remains the same 35) Rise time of an under damped system is Time taken by the response to reach 50 % time taken by the response to reach 95% time taken by the response time to rise from 0 to 100% None of the above 36) Main disadvantage of FM is Complex circuits Adjacent channel interferrence Limited line of sight range Low operating voltage 37) An instantaneous change in voltage is not possible in a current source a capacitor an inductor resistor 38) Which one of the following power semiconductors can be turned on and turned off using the gate ? Power MOSFET GTO SCR Power transistor 39) The roots of the characteristic equation are called Poles Eigen vectors Eigen values Zeroes 40) Which of the following terms is not associated with a sample and a hold circuit? Sample mode Aperture time Conversion time Acquisition time 41) The rms value of sine wave is 0 0.5 1 0.707 42) While measuring power in a three phase circuit using two wattmeters, one of the meter reads zero when pf of the circuit is 1 pf is zero pf is 0.6 when the pf is 0.5 43) Which of the following is used for serial access storage only? Core memory RAM Maganetic disk Magnetic tape 44) Transmission lines are transposed to prevent interference with neighbouring telephone lines reduce copper loss reduce skin effect prevent short-circuit between any two lines 45) The decimal equivalent of binary 10111 is 4 23 16 20 46) The outstanding characteristic of a direct coupled amplifier is its temperature stability avoidance of frequency sensitive components economy ability to amplify DC and low frequency signals 47) The major application of Zener diode is Voltage regulation Rectifier Amplifier Chopper 48) For rural electrification in a country like India with complex network it is preferable to use Air break CB MOCB Oil CB Vacuum CB 49) BJT can be used in the following mode for amplification applications All of the above CE CC CB 50) KVL states that the algebraic sum of the voltage drop around a closed loop in an electric circuit is equal to 1 equal to the input voltage equal to 2 equal to zero 51) A computer can execute only programs written in High level language Assembly language Machine language None of the above 52) An amplifier can be converted to an oscillator using positive feedback null feedback zero feedback negative feedback 53) PUSH and POP operations are connected with PROCESSOR ALU MEMORY STACK 54) In a computer program, the process of executing the same instruction over and over is called None of these Circulating Branching Looping 55) The form factor is the ratio of average value to rms value peak value to average value peak value to rms value rms value to average value 56) A CLASS C power amplifier is one in which the operating point is chosen such that the output current never flows always flows zero for less than one half of I/P cycle zero for more than one half of I/P cycle 57) The full scale input voltage to an ADC is 10V. The resolution required is 5mV. The minimum number of bits required for ADC is 8 12 10 11 58) Star delta starter is used for starting Synchronous motor Squirrel Cage Motor with delta connected stator winding DC Motor Universal Motor 59) Which amplifier configuration has the lowest output impedance ? CC CE CO CB 60) When a 3-phase synchronous motor is running at synchronous speed, the damper winding produces Torque aiding developed torque Eddy current torque Damping torque Zero torque 61) How many layers are available in OSI ? 7 4 6 5 62) The surge impedance of 50 km long underground cable is 50 ohms. For a 25 km length it will be 100 25 50 75 63) The energy stored in the magnetic field is given by 1/2 L²I² 1/2 LI² 1/2 LV² 1/2 L²V² 64) The voltage gain of an emitter follower is always more than 1 less than 1 1 greater than or equal to 1 65) The insulation of modern EHV line is designed based on RI Corona Switching voltage Lightning voltage 66) A resistance is connected in series with an inductive coil. The phase difference between the current and applied voltage decreases with increase in frequency remains constant none of the above increases with increase in supply frequency 67) A 3-phase breaker is rated at 2000 MVA, 33 kV. Its making current will be 49 kA 35 kA 89 kA 70 kA 68) A 3-phase synchronous generator is operating at constant load while the excitation is adjusted to give unity pf current. If the excitation is now increased the pf will become Unity Leading Zero Lagging 69) The impulse ratio of a rod gap is between 1.2 and 1.5 between 1.6 and 1.8 1 between 2 and 2.2 70) For a closed loop system to be stable, the poles of the CLTF must lie none of the above on the left half of the S plane on the right half of the S plane at the origin 71) Which amplifier configuration is used by a push-pull configuration Class C Class AB Class B Class A 72) www stands for Wide world web World wide web Wide world weight World wide weight 73) Modulation is a process to vary Carrier signal by the signal to be transmitted Signal to be transmitted as well as to vary carrier signal by the signal to be transmitted none of the these Signal to be transmitted 74) For a given cross-sectional area of transformer core, stepped cores are used to reduce the magnetizing current to provide more mechanical strength to the core to reduce the core loss to reduce the conductor material 75) Thyrites are used for protection against corona damping surge current over current 76) Which one of the following is not a power semiconductor device ? SCR GTO IGBT CRS 77) While finding the Thevenin equivalent circuit between two terminals, Vth is equal to Open circuit terminal voltage emf of the battery nearest to the terminals Short circuit terminal voltage Net voltage available in the circuit 78) The most important part of an operational amplifier is Differential amplifier Substractor Adder Integrator 79) The following protocol is used used for accessing web pages SMTP FTP PTTP HTTP 80) Input impedance of a transmission line at any distance from the load can be determined using Gant chart none of the above Smith chart Ben chart 81) Micro-programming is a technique for programming input and output programming the control steps of a computer programming the microprocessors writing small programs 82) How many state equations are required to represent a system described by a third order differential equation ? 2 4 2 3 83) A + AB is equal to AB A A + B B 84) Transformer cores are laminated to reduced Ohmic loss Eddy current loss Both eddy current and hysteresis loss Hysteresis loss 85) The following mark up is used for creating webpages HTPP COBOL PASCAL HTML 86) A 3-phase synchronous motor is operating at a load angle of 20° and with excitation voltage equal to the applied voltage. The synchronous reactance drop in terms of excitation voltage 38.2% 69.46% 34.73% 32.9% 87) For maximum transfer of power, internal resistance of the source should be less than load resistance more than load resistance Zero equal to the load resistance 88) The transfer function of a system is given by T(S) = K/[ s³(1+sT) ]. The type and the order of the system are 3 and 2 3 and 4 2 and 3 3 and 3 89) The zero point characteristics for the Potier diagram can be obtained by loading the alternator using Lamp load Water load DC motor Synchronous motor 90) What is the value of modulation index in AM? above 100 between 0 and 1 between -1 and 0 above 1 91) The specification for a standard 74 series TTL gate reads propagation delay as 33ns and power dissipation is 1mV. This circuit is Low speed TTL Standard Schottky TTL Low power Schottky TTL High speed TTL 92) Three identical impedances are connected in delta to a 3-phase supply of 400 Volts. The line current is 34.65 A and the total power taken is 14.4 kW. The resistance of the load in each phase is 10 ohms 16 ohms 12 ohms 20 ohms 93) Donor type impurities all of the above have five valence electrons used to make n-type semiconductors create excess free electrons 94) Which one of the following is not a method of power generation? MHD CHD Thermal Hydroelectric 95) The phase shift between the output and input of a CE amplifier configuration is 270° 360° 90° 180° 96) The gain of the amplifier is usually expressed in Amperes mho Decibels Volts 97) Superposition theorem is applicable only for circuits which are Linear and Bilateral Bilateral Linear Non-linear 98) Which of the following is not a programming language ? ALGOL EIFFEL ADA SUSE LINUX 99) Power in a single phase circuit can be measured using 3 ammeters using one wattmeter using 3 volltmeters using all the above 3 methods 100) The peak overshoot of a second order system is depends on damping ratio is zero is a constant independent on damping ratio |
#3
11th January 2016, 03:37 PM
| |||
| |||
Re: KSEB model question paper
Please give me the previous year question paper for the KSEB examination as I need it for reference purpose?
|
#4
11th January 2016, 03:37 PM
| |||
| |||
Re: KSEB model question paper
The previous year question paper for the KSEB examination is as given below for the Assistant Engineer post: 1. Kirchhoff's laws are valid for A. linear circuit only. B. passive time invariant circuits. C. non-linear circuits only. D. both linear and non-linear circuits.* 2. The time constant of an RL circuit is 1 second and its inductor is 8 H, the resistance of the coil is ..... . A. 8.* B. 1/8. C. 0.25. D. 1. 3. In active filter which element is absent? A. Inductor.* B. Capacitor. C. Both of above. D. Resistor. 4. A capacitor of 50 microfarad is connected in series with a resistance of 120 . If above circuit is connected across 240 V, 50 Hz 1 - supply. Find the capacitive reactance? A. 63.7 .* B. 0.015 C. 135.86 D. 1.765 5. If a resistor and a capacitor are connected to form series R - C circuit across a voltage source. If frequency of voltage source increases A. the current increases.* B. the current decreases. C. the current remain unaltered. D. the current decreases abruptly. 6. A wire 1 m long carries a current of 5 A and is at angle of 30 with B = 1.5 wb/m2 . Magnitude of force A. 2 N. B. 2.5 N. C. 3.75 N.* D. 5 N. 7. Between a hollow and solid metal sphere, charge reside A. On outer surface in hollow and throughout is solid. B. On outer surface in both.* C. On outer surface in solid and throughout hollow. D. None of above. 8. In case of all flux from the current in coil 1 links with coil 2, the coefficient of coupling will be A. 2.0. B. 1.0.* C. 0.5. D. Zero. 9. Both the number of turns and the core length of an inductive coil are doubled. Its self-inductance will be A. unaffected. B. doubled.* C. halved. D. quadrupled. 10. The permanent magnets are made from which of following materials ? A. Soft iron. B. Ferromagnetic.* C. Paramagnetic. D. Diamagnetic. 11. The major cause of creeping in an energy meter is A. over compensation for friction. B. excessive voltage across potential coil.* C. mechanical vibrations. D. stray magnetic field. 12. In a two watt meter method the reading of W1 = 3 kW and W2 = 2 kW. But W2 reading was taken after reversing the current soil of the wattmeter. The net power in the circuit is ....... A. 2 kW. B. 1 kW* C. 3 kW. D. none of these |
|