Jindal Steel Graduate Engineer Trainee syllabus of Electrical and Electronics

Will you please share with me the Jindal Steel Graduate Engineer Trainee syllabus of Electrical and Electronics?

[Arun Vats]

As you want to get the Jindal Steel Graduate Engineer Trainee syllabus of Electrical and Electronics so here it is for you:

Technical subjects to study for written test
Mainly physical metallurgy
Material science,
Fluid mechanics,
SOM,
TOM etc

Written test comprises of two papers that is –
Aptitude Section
Technical Section.

Aptitude Section
READING comprehension,
Preposition
word meanings.

Technical Section
Numerical aptitude
Logical Reasoning
Pattern recognition etc.

Selection process :
Written test
Group Discussion
Technical and H R interview
Physical Fitness Assessment

Here for your reference I am giving you the Jindal Steel Graduate Engineer Trainee Written Exam papers:

1. What is the principle on which centrifugal compressors works ---conversion of K.E to pressure energy
2. _________ has a non linear stress strain curve ---rubber
3. _________has a highest value of poissons ratio----rubber
4. Due to which of the following reasons, the flexible coupling is used----easy to resemble
5. ____________springs are used to absorb shocks and vibrations----torsion
6. Which of the following is correct? -------------absolute pressure =gauge pressure+atmospheric pressure
7. The amount of heat required to raise the temp of 1kg of water through 1degree celcius is callede------- specific heat at constant pressure
8. The value of universal gas constant-------8.314kj/kgdegree k
9. A chemical fuel is a substance which releases_______________on combustion. ----------heat energy
10. The ignition quality of petrol engine fuel is-------octane number
11. For the petrol engine for vehicles the air fuel ratio for maximum power generation is of the order of----12:1
12. Why feausible plug is fitted in a small boiler----to estinguish fire if water level in boiler falls below alarming limit
13. Draught which chimney produces is called----natural draught
14. What is equivalent evaporation---it is the amount of water evaporated from and at 100 degree celsius into dry saturated steam.
15. __________is a none +ve displacement compressor ------reciprocating compressor
16. In a ball bearing______-made harder than stress---ball
17. Hardness is the measure of following----toughness
18. If e=0 the bodies are ---perfectly elastic
19. In cross belt drives the power transmission between pulley rotations is ---opposite disc
20. The internal resistance which the body offers to meet with two load or ext force is called---stress
21. The material having same elastic property in all directio are called as _________ materials---isotropic
22. The bar c/s A is subjected to a tensile force P the normal stress as on oblique plane will be max when inclination of plane to the axis of bar. ---45 degree
23. In which of the following cases unsteady heat flow occurs----aneealing or casing
24. The monochromatic emissivity of white body at all wave lengths and temperature is equal to----unity
25. Due to which of the following reasons hydrogen cnnot be liquified at room temp----don’t know
26. The ratio of specific heat of a liquid to that of specific heat of standard liquid---specific gravity I think\
27. The tendency of an unclosed body to be lifted up in the fluid due to upward force oppp to gravity----buyoyancy
28. An ice cube is floating in a glass of water, as cube melts water level ----falls I think
29. Re=inertia force/viscous force
30. In a cantilever beam of length l L causing a load alone intensity varying uniformly from 0 at the free end to upper unit runs at fixed end. The maximum bending is ---WL2/3
31. The point of contraflexture in a loadd and deforms to the section---bending moment changes sign
32. A simply supported beam of span L is carrying a point load W at the mid span, what is the deflection at the center of beam---WL3/48EI
33. Which of the following is a theroies is suitable for ductile material---maximum shear stress theory
34. in India largest power plant located at----niveli
35. ____steel is widely used for railway track---high carbon
36. _______ is the important component which controls the physical properties of steel---carbon
37. In resistent welding, pression ios released ---after the weld coils
38. Which of the following casting methods are steel and cast iron pipes cast---centrifugal casting
39. When the speed of engine fluctuates continuously above and below mean speed, the governor is said---hunting
40. Which of the gears is recommended for speed reduction ---50:1
41. The flow is said to be turbulent when Re>4000
42. The centrifugal pump calculation is reduced by ---reducing the suction level
43. In rotodynamic pump the increase in energy level is due to ---pressure energy only
44. The working of which of the following hydraulic units is based on Pascals law---hydraulic press
45. Equillibrium condition for coplanar concurrent forces are---sigma H=0, sigma V=0
46. The force which donot meet at one point and line of action donot lie on the same plane is known as _________force. -------must not close
47. The condition of equillibrium for coplanar non concurrent forces are ----sigmaH=0, sigmaV=0, sigma M=0.
47. A__________pair is a pair of 2 equal and opposite forces acting on body in such a way that the lines of action of 2 forces are not in same straight line------couple
48. The % of oxigen by weight in atmosphere is ---23
49. Source o f energy is ---coal, oil, uranium
50. The Fourier law of conduction---Q= -K.a. dt/dx

Hi I am preparing for the placement of Jindal Steel & Power ltd. so for the preparations can you please provide me the previous year placement paper?

[Arun Vats]

Ok, as want the placement of Jindal Steel & Power ltd. so here I am providing you.

Jindal Steel & Power ltd placement paper

Technical Section

It consisted of following questions:-
1. The process of joining two metals is— sintering, thumbling, coining?
2. Ratchet is provided in micrometer screw gauge to-maintain uniform pressure…
3. Strain energy is -the energy stored up to elastic limit..
4. Taper angle is measured by-Sine bar, bevel protector?
5. A centrifugal governor is – Hartnell, Porter, Proell?
6. Numerical on Gate design?
7. Equivalent length in saw is measured from- start point to finish point, from first teeth to last teeth?
8. Anemometer is used for measuring- temperature of air, velocity of air, viscosity of fluid?
9. In neutral equilibrium position of meta center is- coincides with center of gravity..
10. If young’s modulus increases what is the change on thermal coefficient of expansion..?
11. Kaplan turbine- low head, high discharge..
12. Strain- (L-l)/L..
13. Economisor is used for-pre heating feed water..
14. In reciprocating compressor clearance is provided for- cushioning effect and saves the piston from hitting the cylinder head..
15. Function of governor is- maintain a constant speed in parting load conditions..
16. Heat Transfer from hot body to cold body takes place without affecting intervening medium is-radiation..
17. When conduction will not take place-when temp. of both bodies are equal..
18. Which of these defines pitch circle diameter-circular pitch, module,diametral pitch(all of these)..
19. Which of these governor is known as dead weight governor- Portor governor..
20. Property which resist elastic deformation-stiffness..
21. Continuous beam is a beam with- more than 2 supports..
22. More than two supports is known as continuous beam..
23. For self locking of screw-helix angle > friction angle..
24. Involute profile is preferred in gears as-it transmits maximum power..
25. The gear which resists axial thrust-herringbone gears..
26. For large power transmission, square threads- wear out, less efficient, production is costly..
27. The weakest part in flange coupling is-key..
28. Cage is provided in ball bearing to –keep balls in position..
29. When a mass of critically damped style, degree of freedom of system is deflected from its equilibrium position and then it is released then-it will oscillate with increasing time period.
30. 30(+0.05)(-0.03) is- bilateral type of tolerance..
31. Numerical on hoop’s stress?
32. When a cylinder is compressed over another then-hoop stress is reduced.