2023 2024 Student Forum > Management Forum > Main Forum

 
  #2  
11th October 2014, 04:02 PM
Super Moderator
 
Join Date: Apr 2013
Re: I am B.E(CSE) Graduates want to apply for BSNL TTA Exam

You are eligible for the BSNL TTA Exam. The computer science student can apply for BSNL-TTA exam.


Eligibility for BSNL – TTA Exam

The applicant must be Indian residents.
They must be no less than 18 years and not more than 27 years at the time of applying.
The applicant must have cleared their Diploma course in Telecommunication Engineering, Information Technology and Radio Engineering or in Electronics Engineering.

Those who have finished their course in Electrical Engineering, Instruments Technology or in Computer Engineering can also apply for the TTA exam.

Candidates who have cleared the Masters in Electronics course are also entitled to apply.

The candidates must have scored at least 40 percent marks in their final exams. (33% marks for the candidates belonging to the reserved categories.)


Syllabus:
Part- I

General Ability Test 20-Marks
Part-II

Basic Engineering 90-Marks
Part-III

Specialisation 90-Marks

Part-I:-General Ability Test : 20 Marks:
The Candidate’s comprehension and understanding of General English shall be tested through simple exercises such as provision of antonyms and synonyms, fill in the blanks and multiple-choice exercises etc. this shall also include questions on current events, general knowledge and such matters of everyday observation and experience as may be expected of Diploma holder.


The standard of papers in other subject will approximately be that of Diploma level of an Indian Polytechnic. In the specialization Part-III, a candidate has to attempt a common set of questions from the consolidated syllabus prescribed under Specialization Part III. Answer sheet will be OMR based.

There shall be Negative Marking. 25% marks i.e. ¼ mark will be deducted for each wrong answer for the questions carrying 1 mark.
(a) One (1) mark will be awarded for each correct answer.
(b) Zero (0) mark will be awarded for the each un-attempted question.
(c) The final (sub-total and total) marks obtained will not be rounded off.

Part-I:-General Ability Test : 20 Marks:
The Candidate’s comprehension and understanding of General English shall be tested through simple exercises such as provision of antonyms and synonyms, fill in the blanks and multiple-choice exercises etc. this shall also include questions on current events, general knowledge and such matters of everyday observation and experience as may be expected of Diploma holder.

Part -II: Basic Engineering: 90 Marks :

1. Applied Mathematics: Co-ordinate Geometry; Vector Algebras, Matrix ad Determinant; Differential calculus; Integral calculus, Differential equation of second order; Fourier series; Laplace Transformer; Complex Number; Partial Differentiion.

2. Applied Physics: Measurement- Units and Dimensions; Waves, Afcoustics, Ultrasonics; Light; :azer and its Applications; Atomic Structure and Enerty Levels.

3. Basic Electricity: Electrostatics, coulomb’s law, Electric field, Gauss’s theorem, concept of potential difference; concept of capacitance and capacitors; Ohm’s law, power and energy, Kirchoff’s voltage, current laws and their applications in simple DC circuits; Basic Magnetism; Electro Magnetism; Electromagnetic induction; Concept of alternating voltage & current; Cells and Batteries; Voltage and Current Sources; Thevenin’s theorem Norton’s theorem and their applications.

4. Electronic Devices and Circuits: Classification of materials into conductor, semi conductor, Insulator etc. electrical properties, magnetic materials, various types of relays, switches and connectors, Conventional representation of electric and electronic circuit elements. Active and passive components; Semi conductor Physics; Semi Conductor Diode; Bipolar Trnaistor & their circuits; Transistor Biassing & Stabilisation of operating pointl; Single stage transistor amplifier field effect transistor, Mosfet circuit applications, Multistage Transistor Amplifier; Transistor Audio Power Amplifiers; Feedback in Amplifier; Sinusoidal Oscillators; turned voltage Amplifiers; Opto Electronics Devices and their applications; Operational Amplifier; wave shapping and switching circuits. Block diagram of I.C. timer (such as 555) and its working; Multivibrator circuits; Time base circuits; Thyristors and UJT; Regulated Power supply.

5. Digital Technique: Applications and advantages of digital systems; number system(binary and hexadecimal); Logic Gates; Logic simplifications; Codes and Parity; Arithmetic circuits; Decoders, Display Devices and Associated Circuits; Multiplexers and De-Multiplexers; Latches and Flip Flops; counters; Shift Register; Memories; A/D nad D/A converters.

Part -III Specialization: 90 Marks

Electrical :- 3 phase vs single phase supply, Star Delta connections, relation between phase & tine voltage, power factor and their measurements; construction and principles of working of various types of electrical measuring instruments, all types of motor and generator AC & DC transformers, starters, rectifiers, Inverters, battery charges, batteries, servo and stepper motors, contactor control circuits, switchgear, relays, protection devices & schemes, substation, protective relaying, circuit breaker, generator protection, transformer protection, feeder & lightening protection, feeder & bus bar protection, lightening arrestor, earthing, voltage stabilizer 8 regulators, power control devices 8 circuits, phase controlled rectifiers, inverters, choppers, dual converters, cycloconverters; power electronics application in control of drivers refrigeration 8 air conditioning.

Communication:- Modulation and demodulation- Principles and operator of various types of AM, FM and PM modulators / demodulator; pulse modulation- TDM, PAM, PPM, PWM: Multiplexing, principles and applications of PCM. Introduction of Basic block diagram of digital and data communication systems; coding error detection and correction techniques; Digital Modulation Techniques-ASK, ICW, FSK, PSK; Characteristics / working of data transmission circuits; UART: USART: Modems; Protocols and their functions, brief idea of ISDN interfaces, local area Network; Carrier Telephony- Features of carrier telephone system. Microwave

Engineering: Microwave Devices; Waveguides; Microwave Components; Microwave antennas; Microwave communications Systems- Block diagram 7 working principles of microwave communications link.
Network, Filters and Transmission Lines:- Two points network; Attenuators; Filters; Transmission Lines and their applications; characteristic impedance of line; concept of reflection and standing waves on a transmission line; Transmission line equation; Principle of impedance matching; Bandwidth consideration of a transmission fine.

Instruments and Measurements:- Specifications of Instruments- accuracy precision, sensitivity resolution range, Errors in measurement and loading effect; Principles of voltage, current and resistance measurements; Transducers, measurement of displacement a strain, force & torque measuring devices, pressure measuring devices, flow measuring devices power control devices & circuits. Types of AC mill-voltmeters-Amplifier rectifier and rectifier amplifier Block diagram explanation of a basic CRO and a triggerd sweep oscilloscope, front panel controls; Impedance Bridges and Q-Meters; Principles of working and specifications of logic probes, signal analyzer and logic analyzer, signal generator, distortion factor meter, spectrum analyzer.

Control system:- Basic elements of control system, open and closed loop system concepts of feedback, Block diagram of control system. Time lag, hysteresis lineartty concepts; Self regulating and non self regulating control systems. Transfer functions of simple control components, single feedback configuration. Time response of systems; Stability Analysier: Characteristic equation Routh’s table Nyquist Critereon, Relative stability, phase margin and gain margin. Routh Hurwitz criterion, Root Locus technique, Bode Plot, Polar plot, gain margin and phase margin.
Microprocessor- Typical organization of a microcomputer system & functions of its various block; Architecture of a Microprocessor; Memories and I/o interfacing; Brief idea of M/s assembly languages, machines & Mnemonic codes; Instructions format and Addressing mo0de;concept of Instruction set; programming exercises in assembly language; concept of interrupt; Data transfer techniques- sync data transfer, async data transfer interrupt driven data transfer, DMA serial output data, serial input data.



Computers:- Computer and its working, types of computers, familiarization with DOS and windows-concept of file, directory, folder, Number systems; Data Communication. Programming Elements of a high level programming language. PASCAL, c; USE OF BASIS DATA STRUCTURES Fundamentals of computer architecture, Processor design, Control unit design; Memory organization. I/O system Organization. Microprocessor-microprocessor architecture; Instruction set and simple assembly level programming. Microprocessor based system design; typical examples. Personal computers and their typical uses, data communication principles, types and working principles of modems, Network principles, OSI model, functions of data link layer and network layer, networking components; communications protocols-X-25, TCP/IP Database Management System-basic concepts, entity relationship model, relational model, DBMS based on relational model.


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 12:27 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4