|
#2
4th August 2014, 10:02 AM
| |||
| |||
| Re: DMRC Exam Syllabus
Detailed syllabus for the Delhi Metro Rail Corporation is given below which you are looking for . For the post of Jr.Engineers (Electrical/Electronics/Mechanical/Civil), the selection methodology will comprise three-stage process – Written Test (two papers). Personal Interview. Medical examination. The written test will consist of two papers ( Paper-I and Paper-II, to be held on the same day in the same center) . Paper I will consist of multiple-choice objective type questions Paper -II will consist of subjective type questions. Paper-I will consist of multiple-choice objective type questions, on below stated subjects. Aptitude ( Around 20 question) Subject Knowledge ( Around 60 question) General Awareness ( Around 20 question) English ( Around 20 question) Paper-II will consist of subjective type questions on Paragraph Writing Comprehension Essay and questions on Science &Technology matter, in English Medium to judge the candidate’s comprehension skills & test of English language. 1. Mho relay is usually employed for the protection of a) Short lines only b) Medium lines only c) Long lines only d) Any line Ans: Long lines only 2. A modern power semiconductor device IGBT is combines the characteristics of a) BJT and MOSFET b) FCT and GTO c) SCR and MOSFET d) SCR and BJT Ans: BJT and MOSFET 3. For a single-phase a.c. to d.c. controlled rectifier to operate in regenerative mode, which of the following conditions should be satisfied? a) Half –controlled bridge, α 90°, source of e.m.f. in load c) Full-controlled bridge, α > 90°, source of e.m.f. in load d) Full-controlled bridge, α 90°, source of e.m.f. in load 4. Which is the most suitable power device for high frequency ( more 100 kHz) switching application? a) Power MOSFET b) BJT c) SCR d) UJT Ans: Power MOSFET 5. In a thyristor Latching current is ________ than Holding current a) Equal b) Less c) Greater d) None Ans: Greater 6. The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity Ans: 1/11 7. Which one of the following statements for a dc machine which is provided with inter pole winding (IW) as well as compensating winding (CW) is correct a) Both IW and CW are connected in series with Armature winding b) Both IW and CW are connected in parallel with Armature winding c) IW connected in series but CW is connected in parallel with Armature winding d) CW connected in series but IW is connected in parallel with Armature winding Ans: Both IW and CW are connected in series with Armature winding 8. A 0-10 mA PMMC ammeter reads 5mA in a circuit; its bottom control spring snaps out suddenly the meter will now read. a) 5mA b) 10mA c) 2.5mA d) 0 Ans: 0 9. A dc cumulatively compounded motor delivers rated load torque at rated speed. If series field is short circuited, then the armature current and speed will a) Both increases b) Both decreases c) Increases and decreases d) Decreases and increases Ans: Both increases 10. Moving coil in dynamometer wattmeter connected a) In series with fixed coil b) Across supply c) In series with load d) Across load Ans: Across supply 11. In an induction machine, if the air gap increased a) Speed will be reduced b) Efficiency will be improved c) Power factor will be lowered d) Breakdown torque will be reduced Ans: Power factor will be lowered 12. A CRO screen has ten divisions on the horizontal scale. If a voltage signal 5 sin 314t+45 deg)is examined with a line base settings of 5 msec/div, the number of cycles of signal displayed on the screen will be a) 0.5 cycles b) 2.5 cycles c) 5 cycles d) 10 cycles Ans: 2.5 cycles 13. A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W Ans: 0.04, 1160 W 14. Thermocouple is used to measure a) AC b) DC c) Both d) None Ans: Both 15. The two watt meters measurement the ratio of two meter readings is –(1-sqrt3)  1+sqrt3) then the power factor isa) 1 b) 0.866 c) 0.707 d) 0 Ans: 0.707 16. Hays bridge is used to measure___________ and Schering bridge is used to measure____________ a) Inductance, Inductance b) Inductance, Capacitance c) Capacitance, Inductance d) Resistance, Capacitance Ans: Inductance, Capacitance 17. When sine wave is given as input to Schmitt trigger then its generates a) Sine wave b) Saw tooth wave c) Triangle wave d) Square wave Ans: Square wave 18. In Gauss Seidel method the following factors are influenced for operation a) Acceleration factor b) Selection of slack buss c) Both d) None Ans: Selection of slack buss* 19. i. (X’+Y’) A. Low-pass filter function ii. (X’Y’) B. Sum iii. (XY) C. NAND D. Carry E.NOR a) i-C, ii-E, iii-D b) i-C, ii-E, iii-B c) i-C, ii-B, iii-D d) i-C, ii-E, iii-A Ans: i-C, ii-E, iii-D 20. The phase lead compensation is used to a) Increase rise time and decrease overshoot b) Decrease both rise time and overshoot c) Increase both rise time and overshoot d) Decrease rise time and increase overshoot Ans: Decrease rise time and increase overshoot 21. Voltage feed back amplifier is a a) Shunt-Shunt b) Shunt-Series c) Series-Shunt d) Series- Series Ans: Shunt-Shunt 22. In microprocessor the next instruction to be executed is stored in a) Program Counter b) Stack Pointer c) Memory Pointer d) Accumulator Ans: Program Counter 23. The following element retains it energy after source is disconnected a) Resister b) Inductor c) Capacitor d) Thermistor Ans: 24. In series RLC circuit at resonant a) Voltage is in phase with current b) Current is maximum c) Inductive reactance = Capacitive reactance d) All of the above Ans: All of the above 25.For RC low pass filter R=100 K ohms, C= 5 micro farads then lower cutt of frequency is a) 1 K HZ b) 0 HZ c) 381.3 HZ d) Infinity Ans: 26. V=100Sin (1000t+46 deg), I=2Sin (1000t+80 deg) what are the elements in the circuit a) R=30 ohm, L=30 mH b) R=30 ohm, C=33.3 micro farads c) R=40 ohm, L=30 mH d) R=40 ohm, L=33.3 micro farads Ans: R=40 ohm, L=33.3 micro farads |