2023 2024 Student Forum > Management Forum > Main Forum

 
  #2  
13th August 2014, 10:01 AM
Super Moderator
 
Join Date: Apr 2013
Re: BSNL TTA Solved Question paper

You are looking for Bharat Sanchar Nigam Limited TTA Solved Question paper, i am giving here:

(1) The most common modulation system used for telegraphy is

(a) FSK

(b) PSK.

(c) PCM

(d) single tone modulation

(e) Two tone modulation

(2)VSB is an abbreviation of vestigal sideband, is derived by filtering

(a) DSB

(b) AM

(c) either (a) or (b)

(d) PM

(3) The Hartely law states that

(a) The maximum rate of information transmission depends on the depth of modulation

(b) The maximum rate of information depends on the channel bandwidth.

(c) Only binary codes may be used

(d) Redundancy is essential

(4) The FM signal with, a modulation index mf is passed through a frequency tripler. The wave in the output of the tripler will have a modulation index of

(a) mf/9

(b) mf/3

(c) mf

(d) 3 mf

(e) 9mf

(5) In high power AM transmission, modulation is done at

(a) Buffer stage

(b) Oscillator stage

(c) RF power stage

(d) If stage

(6) Companding is used

(a) In delta modulator to combat noise

(b) To limit amplitude in PCM transmitters.

(c) In PWM for working it with TDM

(d) To protect small signals in PCM from quantizing distortion

(e) In PCM to reduce the SNR

(7) In PCM system the SNR of the output signal increases

(a) Inversely with bandwidth

(b) Exponential with bandwidth

(c) With rate of sampling

(d) At low frequencies only

(8) Armstrong modulator generates

(a) Phase modulated signal

(b) Frequency modulated signal

(c) Both of these

(d) Pulse code modulated signal

(e) AM and PCM signals

(9) A Klystron is a cavity acting as buncher and catcher is used as microwave tube for

(a) Guiding waves

(b) Velocity modulation

(c) frequency modulation

(d) impedance matching

(e) All of these

(10) Easily adjustable tuning component in a waveguide is

(a) plunger

(b) plunger and stub

(c) screw

(d) both (a) and (c)

(e) both (b) and (c)

(11) A ferrite is

(a) A non-conductor with magnetic properties

(b) A conductor with magnetic properties

(c) A semiconductors

(d) An insulator which attenuates magnetic fields

(e) A compound with good conductivity.

(12) Vacuum tubes eventually fail at microwave frequencies because of their

(a) Inter electrode capacitance

(b) Small series inductance

(c) Large shunt capacitance

(d) Short transit time

(e) Increased noise figure

(13) The biggest disadvantage the IMP ATT diode has is its

(a) Low Efficiency

(b) high noise

(c) Low BW

(d) inability to provide pulse operation

(e) low power handling ability

(14) In AM transmission the frequency, which is not transmitted is

(a) carrier frequency

(b) audio frequency

(c) upper side frequency

(d) lower side frequency

(15) FM broadcast band lies in

(a) VHF

(b) UHF

(c) SHF

(d) HF

(16) Automatic gain control is used

(a) to maintain the tuning correct

(b) to reduce the voltage of loud passage of music

(c) to maintain the same amount of output, when stations of different strength are received

(d) to increase the amplification at high frequencies

(17) The modulation system inherently is most noise resistant in

(a) SSB suppressed carrier

(b) FM

(c) PPM

(d) PCM

(18) In practical waveguide act as

(a) low pass filter

(b) high pass filter

(c)band pass filter

(d)band stop filter

(19) The antenna efficiencies achieved in practice depend upon

(a) wave length

(b) impedance

(c) frequency

(d) none of above

(20) The process of compressing the digital codes at the transmitter and then expanding them back to their original form at receiver is known as

(a) Quantizing

(b) companding

(c) step sizing

(d) modulation

(21) Digital transmission efficiency is given by

(a) information bits/total bits

(b) total bits/information bits

(c) redundant bits/information bits

(d) none of the above

(22) The speed of BRI ISDN interface is

(a) 2B + D

(b) 2D + B

(c) 30B + D

(d) 30D + B

(23) Which of the following is not a microwave generation source?

(a) Klystron

(b) Magnetron

(c) TWT

(d) Diode

(24) A signal of maximum frequency of 1 KHz is sampled at Nyquist Rate. The interval between two successive samples is:

(a) 50 micro seconds

(b) 100 micro seconds

(c) 500 micro seconds

(d) 1000 micro seconds

(25) In order to get back the original signal, it is necessary to use:

(a) low pass filter

(b) high pass filter

(c) band pass filter

(d) band reject filter

(26) Man made noise id caused by:

(a) Solar eruptions

(b) Distant Stars

(c) Lightning Discharges

(d) Arc discharge in electric machines

(27) At microwave frequencies, the size of antenna becomes

(a) very large

(b) large

(c) small

(d) very small

(28) Due to curvature of earth, microwave repeaters are placed at distance of about

(a) l0 Km

(b) 50 Km

(c) 200 Km

(d) 500 Km

(29) For handling large microwave power, the best medium is

(a) coaxial line

(b) rectangular waveguide

(c) stripline

(d) circular wave guide

(30) An attenuator is used with TWT to

(a) prevent oscillations

(b) increase gain

(c) prevent saturation

(d) help bunching

(3l) TWT is basically

(a) an oscillator

(b) tuned amplifier

(c) wideband amplifier

(d) an audio amplifier

(32) The negative resistance in Gunn diode is due to

(a) electron transfer to a less mobile energy level

(b) high reverse bias

(c) electron domain formation at the junction

(d) tunneling across the junction

(33) Which of the following sinusoidal oscillator is preferred for microwave frequencies?

(a) resonant circuit oscillator

(b) RC phase shift oscillators

(c) negative resistance oscillators

(d) all of the above

(34) When electromagnetic waves are propagated in a waveguide

(a) they travel along the walls of the waveguide

(b) they travel through the dielectric without touching the walls

(c) they are reflected from the walls but do not travel along the walls

(d) none of above

(35) Wave guides are generally made of

(a) Cast iron or steel

(b) White metal or gun metal

(c) bronze or aluminium

(d) plastic or bakelite

(36) The cut off frequency of a wave guide means

(a) lower frequencies will not be propagated

(b) it determines the dimensions of the wave guide

(c) frequency at which zero transmission takes place

(d) None of above

(37) In case of matched load

(a) Transmission is zero

(b) reflection is zero

(c) reflection is unity

(d) transmission is equivalent to reflection

(38) In an AM wave with 100% modulation, the carrier is suppressed. The percentage of power saving will be

(a) 100%

(b) 50%

(c) 25%

(d) 66.7%

(39) The function of AM detector circuit is

(a) to rectify the input signal

(b) to discard the carrier

(c) to provide the audio signal

(d) All of the above

(40) In FM, the noise can be further decreased by

(a) decreasing deviation

(b) increasuig deviation

(c) keeping deviation constant

(d) none of these

(41) In PPM, message resides in

(a) Pulses

(b) time location of pulse edges

(c) none of these

(42) Which of the following pulse systems is preferred for communication in presence of noise?

(a) PAM

(b) PDM

(c) PPM

(d) none of above

(43) Which of the following pulse systems requires higher bandwidth

(a) PAM

(b)PDM

(c)PPM

(d)none of these

(44) The audio frequency range lies between

(a) 20 to 20,000 Hz

(b) 20 to 20,000 KHz

(c) 400 to 8,000Hz

(d) 500 to 5,000 Hz

(45) Maximum undistorted power output of a transmitter is obtained when its modulation is:

(a) more than 100%

(b) 100%

(c) less than 100%

(d) 50%

(46) The AGC voltage in a radio receiver is proportional to

(a) the amount of modulation

(b) the amplitude of audio signal

(c) the amplitude of IF carrier

(d) none of these

(47) An FM transmitter has maximum frequency deviation of 75 KHz and reproduces audio signal up to 15 KHz. Minimum channel width required, in KHz is

(a) 180

(b) 120

(c) 90

(d) 60

(48) With 100% modulation, ratio of side band power to total power transmitted in an amplitude modulated wave is

(a) 2/3

(b) l/3

(c) l/2

(d) l/4

(49) To increase the Q factor of an induction, it wound with

(a) thicker wire

(b) thinner wire

(c) longer wire

(d) wire with heavy insulation

(50) Power factor of a purely resistive circuit is:

(a) zero

(b) one

(c) 0.5

(d) infinity
1. The probability of hitting a target from one gun 9/10, from another gun is 7/10. If both gun are fired at the same time, the probability of hitting the target is

(A) 2/20 (B) 63/100
(C) 16/20 (D) 63/20

2. If the three vectors a, b and c are coplanar , then the missed product a x b. c is

(A) Zero (B) Non-Zero
(C) Unity (D) Non of these

3. Limit sin x/x is x?0

(A) not defined (B) 1
(c) zero (D) -1

4. When a body hits an obstacle, the force with which it hits the obstacle depends upon its

(A) average velocity
(B) velocity at the instant of collision
(C) initial velocity
(D) all of these

5. The wavelength of visible light is of the order of

(A) 1µm (B) 100 µm
(C) 1mm (D) 1 Å

6. Whenever a source of sound moves towards an observer

(A) the frequency heard by the observer is less than that of the source
(B) the frequency heard by the observer is greater than that of the source
(C) the frequency heard by the observer is unchanged
(D) the wavelength of sound heard is greater than that of the sound emitted

7. Moving electric charges will interact with

(A) electric field only
(B) magnetic field only
(C) both of these
(D) none of these

8. Gamma radiation is most similar to

(A) sound waves (B) X-ray
(C) Alpha particles (D) neutrons

9. The fundamental particle responsible for keeping the nucleus together is

(A) meson (B) anti proton
(C) positron (D) muon

10. Air contains 21% oxygen by volume and the rest nitrogen. If the barometer pressure is 740 mm of Hg the partial pressure of oxygen is close to

(A) 155 mm of Hg
(B) 310 mm of Hg
(C) 465 mm of Hg
(D) 162 mm of Hg

11. In the electrolytic cell

(A) electrical energy is converted into chemical energy
(B) chemical energy is converted into electrical energy
(C) mechanical energy is converted into potential energy
(D) potential energy is converted into kinetic energy

12. The force required to maintain a body at constant speed in free space is equal to

(A) the mass of the body
(B) zero
(C) the weight of the body
(D) the force required to stop it

13. If the length of a spring is halved, the spring constant becomes

(A) half (B) 1/4th
(C) double (D) four times

14. The coefficient of static friction depends on

(A) the material of the bodies in contact
(B) the quality of surface finish of the bodies
(C) the presence of foreign matter between the surface
(D) all of these

15. The units of angular impulse in SI system are

(A) Nms (B) Ns
(C) Nm/s (D) Ns/m

16. Stainless steel contains iron and

(A) Chromium and nickel
(B) Chromium and carbon
(C) Nickel and carbon
(D) Chromium and manganese

17. The property of material by which it offers resistance to scratching or indentation is called

(A) Brittleness
(B) Hardness
(C) Toughness
(D) Resilience

18. The failure of a material due to repeated stressing is known as

(A) Creep
(B) Fracture
(C) Fatigue
(D) Brittle Fracture

19. The electric device which blocks DC but allows AC is called

(A) Capacitor
(B) Inductor
(C) Amplifier
(D) Transducer

20. When a charge is moved from one point to another in an electric field, the work done is

(A) independent of the path
(B) zero along the direction of the field
(C) measured in Joules per metre
(D) measure in Volt per metre

21. A capacitor with lowest leakage is

(A) Paper (B) Ceramic
(C) Polyester (D) Mica

22. A zener diode operates

(A) In an extremely high forward bias
(B) In an extremely low reverse bias
(C) In an extremely low forward bias
(D) In a reverse bias higher than laid down voltage

23. The specific gravity of a lead acid cell is often used as a measure of its

(A) Rate of discharge
(B) Operating temperature
(C) State of charge
(D) Life expectancy

24. An uniformly distributed load is one which

(A) Acts at a point on a beam
(B) Spreads uniformly over the whole length of a beam
(C) Varies uniformly over the whole length of a beam
(D) loads the beam from one end only

25. A steam engine device which keeps the speed of the engine, all loads, constant is known as

(A) Flywheel
(B) Eccentric
(C) Connecting rod
(D) Governor

26. The refrigerant hiving the lowest freezing point is

(A) Ammonia
(B) Carbon dioxide
(C) Freon – 11
(D) Freon – 22

27. Heat and work are

(A) Path functions
(B) Properties of a substance
(C) Point functions
(D) Absolute units


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5. The time now is 07:03 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
SEO by vBSEO 3.6.0 PL2

1 2 3 4