BSNL TTA Exam Papers

I want to give BSNL TTA Exam so please provide me previous year’s question papers for preparation?

[Raman Vij]

Here I am providing you previous year’s question papers for preparation of BSNL TTA Exam.

(1) Instrument is a device for determining
(a) the magnitude of a quantity
(b) the physics of a variable
(c) either of the above
(d) both (a) and (b)

(2) Electronic instruments are preferred because they have
(a) no indicating part
(b) low resistance in parallel circuit
(c) very fast response
(d) high resistance in series circuit
(e) no passive elements.

(3) A DC wattmeter essentially consist of
(a) two ammeters
(b) two voltmeters
(c) a voltmeter and an ammeter
(d) a current and potential transformer

(4) Decibel is a unit of
(a) power
(b) impedance
(c) frequency
(d) power ratio

(5) A dc voltmeter may be used directly to measure
(a) frequency
(b) polarity
(c) power factor
(d)power

(6) An accurate voltmeter must have an internal impedance of
(a) very low value
(b) low value
(c) medium value
(d) very high value

(7) The insulation resistance of a transformer winding can be easily measured with
(a) Wheatstone bridge
(b) megger
(c) Kelvin bridge
(d) voltmeter

(8) A 100 V voltmeter has full-scale accuracy of 5%. At its reading of 50 V it will give an error of
(a) 10%
(b) 5%
(c) 2.5%
(d) 1.25%

(9) You are required to check the p. f. of an electric load. No p.f. meter is available. You would
use:
(a) a wattmeter
(b) a ammeter, a voltmeter and a wattmeter
(c) a voltmeter and a ammeter
(d) a kWh meter

(10) The resistance of a field coil may be correctly measured by using
(a) a voltmeter and an ammeter
(b) Schering bridge
(c) a Kelvin double bridge
(d) a Maxwell bridge

(11) An analog instrument has output
(a) Pulsating in nature
(b) Sinusoidal in nature
(c) Which is continuous function of time and bears a constant relation to its input
(d) Independent of the input quantity

(12) Basic charge measuring instrument is
(a) Duddel's oscillograph
(b) Cathode ray oscillograph
(c) Vibration Galvanometer
(d) Bailastic Galvanometer
(e) Battery Charging equipment

(13) A.C. voltage can be measured (using a d.c. instrument) as a value obtained
(a) by subtracting the d.c. reading from it's a.c. reading.
(b) Using the output function of the multimeter
(c) By using a suitable inductor in series with it
(d) By using a parallel capacitor with it
(e) None of the above

(14) A moving coil permanent magnet ammeter can be used to measure
(a) D. C. current only
(b) A. C. current only
(c) A. C. and D. C. currents
(d) voltage by incorporating a shunt resistance
(e) none of these

(15) Select the wrong statement
(a) the internal resistance of the voltmeter must be high
(b) the internal resistance of ammeter must be low
(c) the poor overload capacity is the main disadvantage of hot wires instrument
(d) the check continuity with multimeter, the highest range should be used.
(e) In moving iron voltmeter, frequency compensation is achieved by connecting a capacitor across its fixed coil.

Previous year’s question papers for preparation of BSNL TTA Exam:

BSNL TTA Exam paper 1










BSNL TTA Exam paper 2

BSNL TTA Exam paper 3